Mellerware CELCIUS Manual De Instrucciones página 4

3.3.3. Insert the plug into the wall socket. The indica-
tor light will illuminate.
3.3.4. When the indicator light switches off you may
start ironing.
CAUTION: Iron from low temperature first then move
to high temperature fabrics. Should you need to iron at
a low temperature, after using a high temperature you
must wait for the pilot light to illuminate again or you
will burn your clothes onto the iron. This will void the
warranty.
3.4. Dry ironing:
3.4.1. The iron can be used on the dry setting without
any water in the water tank, it is best to avoid having
the water tank full while dry ironing.
3.4.2. Turn the variable steam control to the minium
position.
3.4.3. Select the setting on the temperature control dial
best suited for the fabric to be used.
3.5. Steam Ironing:
3.5.1. Set the temperature control dial to the "••" or
"•••" position.
3.5.2. Set the variable steam control to the desired
position.
3.6. Spray:
3.6.1. As long as there is enough water in the water
tank, you may use the spray button at any temperature
setting during steam or dry ironing.
3.6.2. Press the spray button several times to activate
the pump while you are ironing.
3.7. Steam blast:
3.7.1. The burst of steam feature provides additional
steam for removing stubborn wrinkles.
3.7.2. Set the temperature control dial between "••"
and "•••" position.
3.7.3. Turn the variable steam control to the maximum
position
3.7.4. Press the powerful steam button to release the
burst of steam.
3.8. Vertical steaming:
3.8.1. It is possible to iron hanging curtains, items of
clothing on a hanger, etc. To do so, follow the instruc-
tions:
3.8.2. Select the maximum temperature of the iron,
while turning the temperature regulator of the iron in a
clockwise direction.
3.8.3. Move the iron in a top to bottom direction while
pressing the steam control. Important: for cotton and
linen, its recommended to put the iron base in contact
with the material.
3.8.4. For other more delicate fibres, it's recommended
to keep the iron base a few centimeters away.
3.9. Once you have finished using the appliance:
3.9.1. Select the minimum position (MIN) using the
thermostat control.
3.9.2. Unplug the appliance from the mains power
supply.
3.9.3. Remove the water from the water tank.
3.9.4. Clean the appliance as described in the cleaning
section.
4. Cleaning
4.1. Disconnect the appliance from the mains power
supply and allow it to cool completely before undertak-
ing any cleaning task.
4.3. Clean the outer parts of the appliance with a damp
cloth with a few drops of washing-up liquid and then
dry. CAUTION! Do not immerse electrical parts of the
appliance in any liquid.
4.4. Do not use solvents, or products with an acid
or base pH such as bleach, or abrasive products, for
cleaning the appliance.
4.5. Never submerge the appliance in water or any
other liquid or place it under running water.
Self-cleaning function:
• It is important to self-clean the appliance at least
once a month to remove calcium and any other
built-up minerals inside the iron.
• Fill the depository to its maximum level, as indi-
cated on "water fill" section.
• Place the iron in a vertical position, plug in to the
mains and select the maximum temperature.
• Leave the appliance to heat up until the pilot
light indicates that it has reached its consigned
temperature.
• Unplug the appliance and place in the sink.
• Press the self-clean button, and keep it pressed
down.
• Let the water flow out through the steam vents in
the base, while lightly shaking the appliance.