Ironing Without Steam - Breville VIN410X Manual Del Usuario

Parts
1. Clean indicator light / Self-clean button
2. Temperature indicator light
3. Iron handset
4. Steam trigger
5. Temperature control dial
6. Lock button
7. Unlock button
8. Removable water tank
9. Power switch (I/O)
10. Base station
11. Steam cord
12. Power cord
13. Cleaning tray
Before using for the first time
Warning: Remove all packaging including any soleplate protection before
operating your steam generator.
1. Wipe over the soleplate with a soft cloth.
2. Position the iron handset on the base station
e
is large enough) or on a heat resistant and secure surface at the same height as
your ironing board.
3. Before connecting your steam generator to the mains supply, make sure your
supply voltage is the same as the one indicated on your steam generator.
4. When you first use your steam generator, there may be a slight odour and it may
smoke slightly for the first few minutes of operation. This is quite normal and will
disappear.
IMPORTANT: On first use the water system will need priming before the handset
will create steam. It is necessary to operate the steam boost function a few times before
the unit will be ready to create steam. To operate the steam boost function, double-click
the steam trigger quickly a number of times untill steam is produced.
r
Cleaning your steam generator before use
Follow these simple steps to remove any impurities or residues inside your steam
generator that may be left over from the manufacturing process.
1. Follow the instructions under filling your steam generator and fill the water tank
as described.
i
2. Empty the water tank to rinse out any foreign particles then refill it.
3. Follow the instructions under steam ironing. Set the temperature to the MAX
setting .
t
4. Iron an old piece of cloth (cotton or towels is ideal) for a few minutes. While
ironing, press the steam trigger
r
need priming and you may need to hold the steam trigger to pull water through
the system and create steam.
5. Any impurities will be flushed from your iron by the steam and absorbed by the
cloth. Your iron is now ready for use.
6
, on your ironing board (if it
a
4 or 5 times. Upon first usage the pump will
Filling your steam generator
1. Remove the water tank by holding the handle and pulling the tank forwards
i
from the base station .
a
2. Slide the water tank out.
3. Fill the water tank with cold tap water to the MAX mark.
4. Slide the water tank back into the base unit until it latches securely into place. You
should hear an audible click.
Filling during use
You can fill your steam generator during use. Simply remove the water tank
described above and add water as required. Do not fill past the MAX indicator mark on
the tank.
Your steam generator will beep twice and the power indicator light
you know that the water tank needs filling.
Steam ironing
The smart features of the iron prevent you from creating steam in temperature settings
below ●●. This is to ensure that delicate fabrics are protected from ironing with steam.
It is recommended that for harder to iron fabrics such as cotton and linen, steam should
be used when ironing.
Warning: When ironing delicate fabrics like nylons, acrylics and synthetics.
Steam should never be used.
1. Fill the water tank with water.
i
2. Plug your steam generator into the mains supply and press the on (I) /off (O)
button to switch your steam generator on.
o
3. Rotate the temperature control dial
setting and the maximum heat (MAX) setting.
4. The temperature indicator light
w
When the temperature indicator light turns solid your steam generator is ready to
use.
5. With the soleplate in contact with the garment, press the steam trigger
couple of seconds. It is not necessary to hold the trigger down continuously as
steam will still be emitted from the soleplate for a short time after the trigger has
been released. If more steam is required, press the steam trigger again.
6. To operate the steam boost function, double-click the steam trigger quickly. The
iron will generate a highly concentrated steam boost for a short period of time.
Always release the steam trigger and allow any residual steam to be released before
replacing the iron on its stand.

Ironing without steam

If you intend to dry-iron fabrics, there is no need to fill the water tank. However, if water
is already in the water tank, you do not need to empty it.
1. Rotate the temperature control dial
setting.
2. When the temperature indicator light
to use.
3. Iron your laundry without pressing the steam trigger
as
i
will flash to let
o
to set the pointer to between the ●●
t
will pulse as your steam generator heats up.
for a
r
to set the pointer to the desired heat
t
turns solid your steam generator is ready
w
.
r
7