DeWalt DW713 Manual Del Usuario página 35

• Make test cuts using scrap material before doing the final cuts.
• All cuts are made in a left bevel and with the back of the moulding
against the base.
INSIDE CORNER
Left side
1. Top of the moulding against the fence.
2. Mitre right.
3. Save the left side of the cut.
Right side
4. Bottom of the moulding against the fence.
5. Mitre left.
6. Save the left side of the cut.
OUTSIDE CORNER
Left side
1. Bottom of the moulding against the fence.
2. Mitre left.
3. Save the left side of the cut.
Right side
4. Top of the moulding against the fence.
5. Mitre right.
6. Save the right side of the cut.
Special Cuts
• All cuts are made with the material secured to the table and against
the fence. Be sure to properly secure workpiece.
BOWED MATERIAL
When cutting bowed material always position it as shown in figure 34
and never like that shown in figure 35. Positioning the material
incorrectly will cause it to pinch the blade near the completion of the
cut.
CUTTING PLASTIC PIPE OR OTHER ROUND MATERIAL
Plastic pipe can be easily cut with your saw. It should be cut just like
wood and clamped or held firmly to the fence to keep it from rolling.
This is extremely important when making angle cuts.
CUTTING LARGE MATERIAL
Occasionally a piece of wood will be too large to fit beneath the blade
guard. A little extra height can be gained by rolling the guard up out of
the way, as shown in figure 36. Avoid doing this as much as possible,
but if need be, the saw will operate properly and make the bigger cut.
NEVER TIE, TAPE, OR OTHERWISE HOLD THE GUARD OPEN WHEN
OPERATING THIS SAW.
Dust Extraction (fi g. 2, 3)
• Fit the dustbag (ff) onto the dust spout (nn).
Connect a dust collection device designed in accordance with the
relevant regulations. The air velocity of externally connected systems
shall be 20 m/s ±2 m/s. Velocity to be measured in the connection tube
at the point of connection, with the tool connected but not running.
Transporting (fi g. 4)
In order to conveniently carry the mitre saw, a carrying handle (a) has
been included on the top of the saw arm.
• To transport the saw, lower the arm and depress the lock down
pin (o).
• Always use the carrying handle (a) or the hand indentations (r)
shown in figure 4 to transport the saw.
MAINTENANCE
Your D WALT power tool has been designed to operate over a long
E
period of time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
All manuals and user guides at all-guides.com
Lubrication
Closed-type, grease-sealed ball bearings are used throughout. These
bearings have sufficient lubrication packed in them at the factory to last
the life of the chop saw.
Cleaning
Optional Accessories
Consult your dealer for further information on the appropriate
accessories.
Protecting the Environment
replacement, or if it is of no further use to you, do not dispose of it with
household waste. Make this product available for separate collection.
WARNING: To reduce the risk of injury, turn unit off
and disconnect machine from power source before
installing and removing accessories, before adjusting or
changing set-ups or when making repairs. Be sure the
trigger switch is in the OFF position. An accidental start-up
can cause injury.
WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into a liquid.
WARNING:: To reduce the risk of injury, regularly clean
the table top.
WARNING: To reduce the risk of injury, regularly clean
the dust collection system.
WARNING: Since accessories, other than those offered
by D WALT, have not been tested with this product, use
E
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only D
accessories should be used with this product.
LASER WARNING:
LASER RADIATION: DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
MAXIMUM OUTPUT POWER
<1MW @ 630 NM – 680 NM
IEC 60825-1 +A1, +A2:2002
LED WORKLIGHT WARNING:
LED RADIATION: DO NOT STARE INTO BEAM
CLASS 2 LED PRODUCT
MAXIMUM OUTPUT POWER
P = 9.2 mW; = 456 nm
peak
IEC 60825-1:1:1993; +A1:1997; +A2:2001
Separate collection. This product must not be disposed of
with normal household waste.
Should you find one day that your D
ENGLISH
WALT, recommended
E
WALT product needs
E
33