Bosch PFS 105 E Manual Original página 14

OBJ_BUCH-420-003.book Page 14 Monday, October 14, 2013 2:59 PM
14 | English
Use and care of the power tool
 Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
 Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
 Use the power tool, accessories and application tools
etc. in accordance with these instructions, taking into
account the working conditions and the work to be per-
formed. Use of power tools for operations different from
those intended could result in a hazardous situation.
Service
 Have your power tool serviced by a qualified repair per-
son using only identical replacement parts. This will en-
sure that the safety of the power tool is maintained.
Safety Warnings for Fine-spray Systems
 Keep area clean well, lit and free of paint or solvent
containers, rags, and other flammable materials.
Spontaneous combustion may occur. Fire extinguisher
equipment shall be present and working at all times.
 Provide for good ventilation in the spraying area and
for sufficient fresh air in the complete room. Evaporat-
ing inflammable solvents create an explosive environment.
 Do not spray and clean with materials that have a flash
point of less than 55 °C. Use materials based on water,
non-volatile hydrocarbons or similar materials. Volatile
evaporating solvents create an explosive environment.
 Do not spray in the vicininty of ignition sources, such as
static electricity sparks, open flames, pilot lights, hot
objects, engines/motors, cigarettes and sparks from
plugging in or unplugging power cords or operating
switches. Such spark sources can ignite the spraying vi-
cinity/environment.
 Do not spray any liquid of unknown hazard potential.
Unknown materials can create hazardous conditions.
 Wear additional protective equipment such as appro-
priate protective gloves and protective masks or respi-
rators when spraying or handling chemicals. Wearing
protective equipment for the appropriate conditions re-
duces the exposure to hazardous substances.
 Be aware of possible hazards from the spray material.
Observe the information on drums/tanks/tins as well
as manufacturer information of the spray material, in-
cluding the request to wear personal protective equip-
ment. The manufacturer's instructions are to be observed
in order to reduce the risk of fire as well as injuries caused
through toxins, carcinogens, etc.
 Keep the plug of the mains cord and the trigger switch
of the spray gun clear of paint and other fluids. Never
1 609 92A 0BR | (14.10.13)
hold the cord by its connectors to support it. Failure to
follow the instruction can lead to electric shock.
 Supervise children. This will ensure that children do not
play with the fine-spray system.
 This fine-spray system can be used by children aged 8
or older and by persons who have physical, sensory or
mental limitations or a lack of experience or knowledge
if they have been supervised or instructed in the safe
operation of the fine-spray system and understand the
associated dangers. Otherwise, there is a danger of oper-
ating errors and injuries.
 Children must not be allowed to clean and perform main-
tenance on the fine-spray system without supervision.
Products sold in GB only: Your product is fitted with a
BS 1363/A approved electric plug with internal fuse (ASTA
approved to BS 1362).
If the plug is not suitable for your socket outlets, it should be
cut off and an appropriate plug fitted in its place by an author-
ised customer service agent. The replacement plug should
have the same fuse rating as the original plug.
The severed plug must be disposed of to avoid a possible
shock hazard and should never be inserted into a mains sock-
et elsewhere.
Products sold in AUS and NZ only: Use a residual current de-
vice (RCD) with a rated residual current of 30 mA or less.
Product Description and Specifications
Read all safety warnings and all instruc-
tions. Failure to follow the warnings and in-
structions may result in electric shock, fire
and/or serious injury.
Intended Use
The power tool is only intended for atomising solvent-based
and water-dilutable lacquers, glazes, primers, clear lacquers,
automotive top coats, wood stains and oils.
The power tool is not suitable for use with dispersion and latex
paints, caustic solutions, acidic coating materials, spray ma-
terial containing grains or solids, and spatter and drip resist-
ant materials.
Product Features
The numbering of the components shown refers to the repre-
sentation of the power tool on the graphic pages.
1 Spray gun
2 Air cap
3 Union nut
4 Mark for SDS connection
5 Thumbwheel for spraying capacity
6 Hose port (spray gun)
7 Handle extension (only for 800 ml container)
8 Container for spray material, 800 ml
Container for spray material, 600 ml*
9 Trigger switch
10 Suction tube with container seal
green: for 800 ml container
white: for 600 ml container*
Bosch Power Tools