DeWalt DWE46101 Traducido De Las Instrucciones Originales página 41

Attaching Side Handle (fi g. 1)
WARNING: Before using the tool,
check that the handle is tightened
securely.
Screw the side handle (c) tightly into one of the holes
(p) on either side of the gear case.
Mounting and Removing Mortar
Raking Shroud (fi g. 3)
NOTE: The supplied mortar raking shroud is only
recommended for use with the DWE46101 heavy-
duty mortar raking motor.
1. Open the clamp lever (n) on the tuckpoint
shroud and align the tabs (q) on the tuckpoint
shroud with the slots (r) on the grinder gear
case.
2. With the clamp lever open, rotate the shroud
into the desired working position. The shroud
should be positioned between the spindle and
the operator to provide optimum efficiency.
3. Close the clamp lever (n) to secure the tuckpoint
shroud on the gear case. Do not operate the
grinder with a loose tuckpoint shroud or the
clamp lever in open position.
4. To remove the tuckpoint shroud, open the
clamp lever, rotate the tuckpoint shroud to align
the slots and tabs and pull up on the tuckpoint
shroud.
NOTE: The tuckpoint shroud is pre-adjusted to the
diameter of the gear case hub at the factory. If, after
a period of time, the tuckpoint shroud becomes
loose, tighten the clamp adjusting screw (i) with
clamp lever in the closed position.
NOTICE: Do not tighten the clamp
adjusting screw with the clamp lever in
open position. Undetectable damage to
the tuckpoint shroud or the mounting
hub may result.
NOTICE: If tuckpoint shroud cannot be
tightened by the clamp adjusting clamp,
do not use tool. Take the tool and
tuckpoint shroud to a service center to
repair or replace the tuckpoint shroud.
Fitting and Removing a Cutting Disc
(fi g. 1, 4)
WARNING: Do not use a damaged
disc.
1. With shroud installed, place the tool on a table,
spindle up.
2. Fit the backing flange (d) correctly onto the
spindle (b) (fig. 4).
3. Rotate open the cornering door (m) and place
the cutting disc (u) on the backing flange (d).
4. Screw the threaded clamp nut (e) onto the
spindle (b).
5. Press the spindle lock button (a) and rotate the
spindle (b) until it locks in position.
6. Tighten the threaded clamp nut (e) with the two-
pin spanner supplied.
7. Release the spindle lock.
8. Close and secure the cornering door (m) by
tightening the cornering door locking lever (l).
9. To remove the disc, loosen the threaded clamp
nut (e) with the two-pin spanner.
Mortar Raking Shroud (fi g. 6)
WARNING: Only Type 1 diamond
wheels shall be used with tuck-
point shroud. Do not cut metal. Do not
use with bonded abrasive wheels.
Follow the Fitting and Removing a Cutting Disc
instructions and mount the grinding disc.
It may be necessary to open the cornering door
to install 125 mm tuckpointing wheels, refer to
Cornering Door Application.
DEPTH OF CUT ADJUSTMENT (FIG. 5)
1. Loosen the depth of cut shoe locking knob (k).
2. Slide the depth of cut shoe (j) to the desired
position.
3. Tighten depth of cut shoe locking knob.
CORNER DOOR APPLICATION (FIG. 6)
WARNING: To reduce the risk
of injury, ALWAYS turn the tool
off and disconnect the tool from
the power source before making
any adjustments or removing
or installing attachments or
accessories. This applies to both
the grinder and the dust extractor
vacuum. Such preventative safety
measures reduce the risk of starting the
tool accidentally.
WARNING: Risk of personal injury. The
corner door should only be opened for
cutting inside corners. Keep hands and
body away from cutting area at all times.
Ensure corner door is closed in all other
applications.
This feature allows the cutting of an inside corner.
1. Ensure the tool is off and wheel has come to a
complete stop.
EN GL IS H
39