Hozelock KILLASPRAY PLUS Manual De Instrucciones página 4

33796-002 KillaSprayPlus5-7-10 Inst
Maintenance • Entretien • Onderhoud • Mantenimiento • Underhåll • Wartung • Vedlikehold • Huolto
Vedligehold • Manutenzione • Manutenção • Konserwacja • Συντήρηση • Bakım • Karbantartás • Údrãba
29
GB
k s
illa pray
Instructions & Warnings
• Before carrying out any maintenance on this sprayer, it is
essential to depressurise the bottle by activating the pressure
release valve.
• This sprayer is intended for use with water-based solutions of:
insecticides, fungicides, weedkillers & fertilizers.
• Always follow the chemical suppliers instructions, as well as
the instructions supplied with this sprayer.
Always wear protective clothing, goggles, face mask and
gloves.
Avoid inhaling spray mist.
Avoid skin contact with chemicals.
Always work in a well ventilated area.
Take care to protect children pets & fish from exposure to
chemicals.
Always wash hands thoroughly after use & especially before
eating.
Always wash any contaminated clothing.
Seek medical attention if spray gets in your eyes or you
develop any symptoms after spraying.
Do not spray near food or food preparation areas.When
spraying crops, pay particular attention to the chemical
manufacturers advice on time before crops can be eaten.
Do not spray any solvent e.g. White spirit.
Spray only thin watery solutions; thicker mixtures will clog
the nozzle.
Powdered chemicals can be sprayed successfully if they are
completely soluble in water. If they are not, or the solution
tends to settle, spraying can still be successful if the mixture
is continually agitated.
22/11/07
Обслуживание • Hooldus • Apkope • Remontas
A
A
A
X
X
p
lus
17:38 Page 4
30
G H
B
D
C
32
J
If the material to be sprayed contains sediment, strain the
liquid into the sprayer bottle.
Do not over pressurise the bottle, or tamper with the
pressure release valve. The pressure release valve is
designed to release excess pressure do not interfere with it
or force it to remain closed.
Winter Use – drain liquid from all parts and prevent damage
from freezing.
Annual maintenance – At least once per year thoroughly
clean the whole sprayer and apply silicone grease to all
moving parts & seals. Test with water, and if any washer or
seal has perished it must be replaced.
Notes
• Before carry out any maintenance on this sprayer. It is essential
to depressurise the bottle by activating the pressure release
valve.
A
Make sure all nuts are screwed hand tight before use.
B
This sprayer is made from many different types of plastic,
and although the liquid you wish to spray may be packed in
plastic, this does not guarantee it will not damage the sprayer.
If you have any doubt about compatibility contact Hozelock
consumer services. When filling the sprayer ensure that the
maximum fill level is not exceeded.
C
Ensure that the pump is screwed into the bottle tightly.
D
Operate the pressure release valve manually to ensure it is
functioning correctly and able to move.
E
If the sprayer has been used with chemicals, discard safely any
unused solution after use.
F
Fill sprayer with warm water (not hot),
re-assemble the sprayer and spray some of the contents.
Repeat; check that the nozzle is free from sediment.
If necessary repeat the process until the sprayer is clean.
NB : Do not use detergent.
G
The pump O-ring should be lubricated to allow the sprayer to
pump air efficiently. Apply silicone grease regularly, to the
pump O-rings (A).
H
The nozzle cap (B) & swirl grooves (C) should be kept clean
and free of obstruction. The O-ring should be lubricated to
allow the spray pattern to be easily changed. Apply silicone
grease regularly, to the nozzle O-ring (D).
31
I