Kinderkraft GRANDE Manual De Usuario página 13

• To avoid injury ensure that the child is kept away when
unfolding and folding this product.
• Do not let the child play with this product.
• Always use the restraint system.
• Check that the pram body or seat unit or car seat attachment
devices are correctly engaged before use.
• This product is not suitable for running or skating.
•
Age and weight usage: from 0 months up to 15 kg.
•
We recommend using lowest reclined position for newborn babies.
•
This product may only be used by one child at the same time
•
The parking device shall be engaged when placing and removing the children
•
The maximum basket load is 2 kg.
•
Maximum weight of a bag attached to the adjustable handle is 1 kg.
•
Any additional load suspended from the buggy handles, backrest and sides will cause stability loss.
•
Use only parts and accessories supplied or recommended by the manufacturer. Do not use other parts or accessories.
•
Lift the front suspension when going up a curb or step.
•
Do not place the product near open flame or other heat sources.
•
Do not use with an additional platform.
B. ASSEMBLY
I. BUGGY COMPONENTS (FIG. 1)
A. Frame with seat and safety straps
B. Front wheels
C. Rear wheels
D. Safety bar
II. UNFOLDING BUGGY FRAME Place the frame on a flat surface with its handle up (FIG. 2). In order to unfold the frame,
slide the lock (2A) located on the parent handle, then press the button (2B) and lift the frame upwards following the arrow
in Figure 2C until you hear the locking sound. Make sure that the buggy cover is properly attached to the Velcro fasteners
on both sides of the buggy (FIG. 3). NOTE! Make sure that the attachments on the inner side of the buggy material are
inserted into the hooks, and the press studs are closed (FIG. 16). A properly unfolded frame is shown in FIG. 4.
III. WHEEL ASSEMBLY/DISASSEMBLY Insert the rear wheels in the rear axles holes until you hear the locking sound (FIG. 5).
In order to remove the rear wheels (FIG. 6), unlock the locking button located on both sides of the rear axle (6A) while
pulling the wheels out of the slots (6B). Insert the front wheels in the front axles until you hear the locking sound (FIG. 7).
To remove the front wheels, push the quick release button located below the footrest under each wheel (FIG. 8). The buggy
has a system of swivel front wheels which can be locked in the straight-ahead position. To lock the wheel to move forward,
slide the ring located above the wheel (FIG 9).
NOTE! Before using the buggy, make sure that all the wheels are
properly installed.
IV. ASSEMBLY/DISASSEMBLY OF THE SAFETY BAR AND LEG COVER, CANOPY ADJUSTMENT The safety bar must be inserted
in appropriate slots on both sides of the frame, as shown in Figure 10. To remove the bar, press the buttons on both sides
and remove the bar (FIG. 11). Leg cover has four Velcro fasteners located on the inner side. In order to attach the cover,
fasten the Velcro fasteners on the seat frame tubes. To adjust and unfold another layer of material, unfasten the zip located
on the canopy (FIG. 12A and 12B).
V. USE OF BRAKE The buggy is equipped with a foot brake located on the rear axle. Press the lower part of the brake down;
the brake is activated when you hear the locking sound (FIG. 13). Unlocking occurs after lifting the lower part of brake lever.
VI. BACK AND FOOTREST ADJUSTMENT AND CUP HOLDER ASSEMBLY (FIG. 14) The seat is equipped with smooth backrest
adjustment system, from a lying to a sitting position, using a clasp (14A). The footrest has 3 positions. Press the buttons on
both sides (14B) to change the footrest position. Cup holder is mounted on the left side of the buggy on the stem (14C).
VII. SAFETY STRAPS (FIG. 15) The buggy's straps are adapted in such a way to enable its use even by newborns. Always use
the fastening system. To secure the child, connect the latches of the hip and shoulder straps (15A) and then insert them into
E. Cup holder
F. Leg cover
G. Rain cover
13