Important Safety Instructions - Biamp Vocia VA-2060 Manual De Operación

1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this product near water.
6) Clean only with dry cloth.
7) Do not block ventilation openings. Install in accordance with
the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the grounding-type plug.
A grounding type plug has two blades and a third grounding
prong.
The third prong is provided for your safety. If the provided
plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched,
particularly at plugs, convenience receptacles and the point
where they exit from the product.
Explanation of Graphical Symbols:
Lightning Bolt: Hazardous Live voltages present when this unit is in operation. Do not touch terminals marked with
this symbol while the unit is connected to live power.
Exclamation Point: Replace components (i.e. fuses) only with the values specified by the manufacturer. Failure to
do so will compromise safe operation of this unit
Hazardous Moving Fan Blades: Remove power before servicing and keep away from moving fan blades.
WARNING - To reduce the risk of fire or electric shock, do not expose these products to rain or moisture. These products must not be
exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on these products.
WARNING – 100 Volt Speaker terminals marked with the symbol
requires installation by a Skilled or Instructed Person.
WARNING – MAINS Powered Products employ Safety Grounding and must be connected to a MAINS socket that is properly grounded to
provide a protective earthing connection.
Disconnect Device - The MAINS plug is used to disconnect MAINS power and must remain readily operable.
CAUTION – When POTS Telephone Interface options are provided, connections to the telecom circuits of this device must be made by
qualified, trained personnel. To reduce the risk of fire, use only No. 26 AWG solid copper wire for telecom circuit connections.
Intended for Installation and Service by Skilled Personnel Only:
CAUTION – To reduce the Risk of Electric Shock, Installation and Service of Biamp Products should be conducted only by Skilled Persons
who are Biamp Qualified Audio Installation Professionals.
Do not perform any servicing other than that contained in the Operating Instructions unless you are a Skilled Person qualified to do so.
Skilled Persons must disconnect AC MAINS Power before opening product.
CAUTION - The Installation steps for 'Auxiliary Power' are for use by Skilled Personnel only and must comply with all local codes.
• National Electrical Code, ANSI/NFPA 70 for United States.
• Canadian Electrical Code, Part 1, CSA C22.1, Sections 2-128, 12-010(3) and 12-100 for Canada.
Wall Mounting Instructions – Wall mounted products must be securely fastened to drywall or similar surface using a minimum of 4 wood
screws (2 screws for product with only two mounting holes). Alternate fasteners which may be used include drywall anchors, self-tapping
sheet metal screws located in metal studs or wood screws extending a minimum of ½ inch into wood studs.

IMPORTANT SAFETY INSTRUCTIONS

are Hazardous Live. External wiring connected to these terminals
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with equipment rack, cart, stand or
table designed to provide adequate mechanical
strength, heat dissipation and securement to the
building structure.
When a cart is used, use caution when moving
the cart and product combination to avoid injury from tip-over.
13) Unplug this product during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the product has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the product, the product has
been exposed to rain or moisture, does not operate normally, or
has been dropped.