Black and Decker FSMH1621D Manual De Instrucciones página 8

ENGLISH
Pulling the handle (10) back will activate the steam pump.
u
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
It takes a few seconds for steam to enter the cleaning pad.
u
The steam mop will now glide easily over the surface to be
sanitised/cleaned.
Push and pull the steam mop slowly across the floor to
u
thoroughly steam clean each section.
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to leave the steam mop for a short time so that
you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
When you have finished using the steam mop, return the
u
handle (10) to the upright position and turn it 'OFF' and
wait until the steam mop cools down. (approximately five
minutes)
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, re-
turn the handle (10) to the upright position and turn the steam
mop 'OFF'. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
Carpet refreshing
Place a cleaning pad (12) on the floor with the 'hook &
u
loop' side facing up.
Lightly press the steam mop down onto the cleaning pad
u
(12).
Place the carpet glider (14) on the floor.
u
Lightly press the steam mop down onto the carpet glider
u
(14) until it clicks into place.
Connect the steam mop to the mains.
u
Press the ON/OFF button (1). It takes approximately 15
u
seconds for the steam mop to heat up.
Press the Autoselect button (6) to the Wood/Laminate
TM
u
setting.
Pulling the handle (10) back will activate the steam pump.
u
After a few seconds steam will start to come out of the
steam head.
Note: When first filled or after running dry it can take up to 45
seconds for steam to be produced.
Push and pull the steam mop slowly across the carpet to
u
thoroughly refresh each section.
8
(Original instructions)
Note: During use you may turn off the steam pump by return-
ing the handle to the upright position, this convenient feature
will allow you to leave the steam mop for a short time so that
you may move items of furniture, then continue cleaning
without the need to switch the appliance off.
When you have finished using the steam mop, return the
u
handle (10) to the upright position and turn it 'OFF' and
wait until the steam mop cools down. (approximately five
minutes)
Caution! If steam is observed escaping from the join between
the hand held steam cleaner and the steam mop body, switch
off and disconnect the unit from the mains supply. Allow to
cool. Remove the hand held steam cleaner from the steam
mop body. Inspect the seal (26) on the steam nozzle (4) and
hose (27) (fig. J). If the seal is missing or damaged then
please contact your nearest authorised repair agent. Do not
use the appliance. If the seal is in good condition re-fit the
hand held steam cleaner to the steam mop body ensuring that
it is seated firmly in place.
Caution! It is important to monitor the water level in the water
tank. To refill the water tank and continue to sanitise/clean, re-
turn the handle (10) to the upright position and turn the steam
mop 'OFF'. Unplug the unit from the electrical wall outlet, refill
the water tank (8).
Caution! Never leave the steam mop in one spot on any
surface for any period of time. Always place the steam mop
with the handle (10) in the upright position when stationary
and make sure the steam mop is turned off when not in use.
After use (Fig. M & N)
Return the handle (10) to the upright position and turn the
u
steam mop 'OFF',
Wait until the steam mop cools down. (approximately five
u
minutes)
Unplug the steam mop from the electrical wall outlet.
u
Empty the water tank (8).
u
Remove the cleaning pad (12) and wash it ready for
u
next use. (Take care to follow the wash care instructions
printed on the cleaning pad).
Wrap the supply cable around the cable tidy hooks (15 &
u
16).
Note: The top cable tidy hook (16) rotates to easily release
the cable ready for next use.
Clip the supply cable onto itself using the cable tidy clip
u
(32) close to the plug.
Note: With the handle (10) in the upright position, the cable
neatly wrapped around the cable tidy hooks (15 & 16) and
secured with the cable tidy clip (32) your steam mop will stand
on its own for storage. Alternatively there is a hanging bracket
(33) built into the hand grip (34) which will allow your steam
mop to be hung from a suitable hook on the wall. Always
ensure that your wall hook is capable of supporting the weight
of the steam mop safely.