Lamp (Re)Placement; Overhead Rigging - JB Systems Light STR-300 Manual De Instrucciones

ENGLISH

LAMP (RE)PLACEMENT

In case of replacement of the lamp or maintenance, do not open the fixture within 15
minutes until the unit cools down after switching off. Always unplug the unit before
servicing! Always use the same type of spare parts (bulbs, fuses, etc.) When replacing
parts, please only genuine spare parts.
1. Switch off the unit and unplug the mains cable.
2. Wait for about 15 minutes until the unit has been cooled down.
3. Use a pincer to unscrew the 3 nuts of the safety screen.
4. Remove the safety screen.
5. On the inside you will see the lamp socket. Unplug the old lamp. Hold the lamp socket while pressing
the new lamp gently in the socket.
Attention! Check the label on the backside of the device or see the technical specifications in this
manual to know which lamp should be used. Never install lamps with a higher wattage
6. Don't touch the bulb with bare hands! This drastically shortens the lifespan of the lamp. If you touched
the lamp, clean it with a cloth and a little denatured alcohol. Wipe the lamp off before installing.
7. Put the safety screen back on the unit and close it with the 3 nuts
8. Done!

OVERHEAD RIGGING

 Important: The installation must be carried out by qualified service personal only. Improper
installation can result in serious injuries and/or damage to property. Overhead rigging requires
extensive experience! Working load limits should be respected, certified installation materials
should be used, the installed device should be inspected regularly for safety.
 Make sure the area below the installation place is free from unwanted persons during rigging, de-rigging
and servicing.
 Locate the fixture in a well ventilated spot, far away from any flammable materials and/or liquids. The
fixture must be fixed at least 50cm from surrounding walls.
 The device should be installed out of reach of people and outside areas where persons may walk by or be
seated.
 Before rigging make sure that the installation area can hold a minimum point load of 10times the device's
weight.
 Always use a certified safety cable that can hold 12times the weight of the device when installing the unit.
This secondary safety attachment should be installed in a way that no part of the installation can drop
more than 20cm if the main attachment fails.
 The device should be well fixed; a free-swinging mounting is dangerous and may not be considered!
 Don't cover any ventilation openings as this may result in overheating.
 The operator has to make sure that the safety-relating and machine-technical installations are approved by
an expert before using them for the first time. The installations should be inspected every year by a skilled
person to be sure that safety is still optimal.
OPERATING INSTRUCTIONS
 Once connected to the mains the device starts running.
 Regular breaks during operation are essential to maximize the life of this device as it is not designed for
continual use.
 Do not switch the unit on and off in short time intervals as this reduces the lamp life.
 Don't touch the housing with bare-hands during its operation.
 Always unplug the unit when it is not used for a longer time or before replacing the bulb or start servicing.
 In the event of serious operating problems, stop using the fixture and contact your dealer immediately.
 Important: Never look directly into the light source! Don't use the effect in the presence of persons
suffering from epilepsy.
JB SYSTEMS®
OPERATION MANUAL
3/30 STR-300
ENGLISH
DESCRIPTION(FRONT)
1. Safety Screen: This screen prevents that you can touch the bulb with bare hands.
2. Hanging Bracket: with 2 knobs on both sides to fasten the unit and a mounting hole to fix a mounting
hook.
3. Bulb: The bulb of the STR-300 unit is a special XENON 75 W strobe lamp.
DESCRIPTION(REAR)
1. Dual 1\4 inch Mono jack: Used to create synchronous operations with multiple STR-300.

Input: is used to connect a remote control ( the FL01CX or BF04/D remote control of JB Systems )
to the first STR-300 or to connect a jack cable that comes from the output of a previous STR-300.

Output: is used to connect a jack cable that goes to the input of the next STR-300.
Important: The amount of units that you can "Daisy Chain" is limited to 5 units !
2. Speed knob: This knob is used to adjust the flash rate when no remote control is connected.
3. Fuse Holder
4. Mains cable
JB SYSTEMS®
OPERATION MANUAL
4/30 STR-300