Bosch PMF 10,8 LI Manual Original página 22

Ocultar thumbs Ver también para PMF 10,8 LI:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 40
OBJ_BUCH-1170-002.book Page 22 Tuesday, May 11, 2010 3:36 PM
22 | English
Accessory
HCS plunge
cut saw
blades, wood
BIM plunge
cut saw
blades, metal
HM-Riff seg-
ment saw
blade
HM-Riff delta
plate
Scraper, rigid
Mounting/Replacing the Application Tool/
Accessory
If required, remove an already mounted applica-
tion tool/accessory.
For removing the application tool/accessory
loosen the screw 10 with the allen key 11 and re-
move the tool.
Mount the application tool/accessory (e.g.
plunge cut saw blade 9) in such a way on the
tool holder 7 that the openings of the tool en-
gage into the cams of the tool holder.
For a safe and fatigue-free working position it is
possible to position the application tools/acces-
sories in any snap-in positions on the tool hold-
er. Position the tool in such a way that the de-
pressed centre points downwards (marking on
the tool is readable from above, see figure on
the graphics page).
Use the screw 10 to fasten the application
tool/accessory. Tightly fasten the screw 10 with
the allen key 11.
Check the tight seating of the application
tool/accessory. Incorrect or not securely fas-
tened application tools/accessories can come
loose during operation and pose a hazard.
2 609 004 157 | (11.5.10)
Material
Application
Wooden materials,
Smaller separating and plunge cuts;
soft plastics
Example: Cut-outs in furniture for cable con-
nections
Metal (e.g. unhard-
Smaller separating and plunge cuts;
ened nails, screws,
Example: Shortening narrow profiles, cutting
smaller profiles),
fastening elements such as staples
non-ferrous metals
Grouting joints, soft
Cutting and separating close to edges, in cor-
wall tiles, glass-fibre
ners or hard to reach areas;
reinforces plastic
Example: Removing grouting joints between
and other abrasive
wall tiles for repair work, cutting openings in
materials
tiles, gypsum boards or plastic
Mortar, concrete
Rasping and sanding on hard surfaces;
remainders, wood,
Example: Removing mortar or tile adhesive
abrasive materials
(e.g. when replacing damaged tiles)
Carpets, coverings
Scraping on hard surfaces;
Example: Removing carpet and tile adhesive
Mounting/Replacing a Sanding Sheet on the
Sanding Plate
The sanding plate 12 is fitted with Velcro back-
ing for quick and easy fastening of sanding
sheets with Velcro adhesion.
Before attaching the sanding sheet 13, free the
Velcro backing of the sanding plate 12 from any
debris by tapping against it in order to enable
optimum adhesion.
Position the sanding sheet 13 flush alongside
one edge of the sanding plate 12, then lay the
sanding sheet onto the sanding plate and press
firmly.
To ensure optimum dust extraction, pay atten-
tion that the punched holes in the sanding sheet
match with the holes in the sanding plate.
To remove the sanding sheet 13, grasp it at one of
the tips and pull it off from the sanding plate 12.
You can use all sanding sheets, fleece pads/
polishing cloth pads of the Delta 93 mm series
of Bosch accessory program.
Sanding accessories, such as fleece pads/pol-
ishing cloth pads, are attached to the sanding
plate in the same manner.
Bosch Power Tools

Publicidad

Tabla de contenido
loading

Tabla de contenido