DeWalt DXV34P Traducido De Las Instrucciones Originales página 17

English
Description (Fig. A)
WARNING : Never modify the power appliance or
any part of it. Damage or personal injury could result.
Top handle/cord wrap
1
Power cord
2
On/off power switch
3
Vacuum head
4
Canister latch
5
Canister
6
Suction hose
7
Casters
8
Filters
9
Threaded hose inlet
10
Hose strap
11
12 Bag
ASSEMBLY AND ADJUSTMENTS (Fig. A–C)
WARNING: To reduce the risk of injury, turn
appliance off and disconnect appliance from
power source before installing and removing
accessories, before adjusting or changing
set-ups or when making repairs.
start-up can cause injury.
WARNING: The lters
place while vacuuming, except as described
under Wet Pick Up Applications
When vacuuming ne dust, you may also use an
additional paper bag or eece bag to make
emptying the canister easier.
1. If optional paper or fleece bag
install as shown in Figure B.
NOTE: Be careful not to tear the bag. Place bag
securely onto inlet to provide a tight seal for
10
maximum dust collection performance.
2. Place the vacuum head
secure it by closing the canister latches
3. Insert end of hose into threaded hose inlet
7
and tighten the end of hose on to the tank.
OPERATION
Instructions for Use (Fig. A, D, E)
WARNING:
Always observe the safety instructions
and applicable regulations.
WARNING: To reduce the risk of injury,
turn appliance off and disconnect
appliance from power source before
installing and removing accessories,
before adjusting or changing set-ups or
when making repairs.
cause injury.
1. Plug the power cord into an appropriate outlet.
2. Turn the on/off switch
3. Your D WALT construction dust extractor is tted
E
with the D WALT connection system. The allows for
E
a fast, secure connection between the suction hose
and power tool. The connector
7
An accidental
must always be in
9
under Operation.
is to be used,
12
onto the canister and
4
.
5
10
An accidental start-up can
to the ON position ( I ).
3
connects
13
directly to DeWALT compatible tools or through the
use of an adapter (available from your local D
supplier). Refer to the Accessories section for detail
on available adapters.
NOTE:
If using an adapter ensure it is firmly
attached to the tool outlet before following the steps
below.
OPERATING INSTRUCTIONS
Caster installation (Fig. A, F)
1.Invert the dust box and install the casters to the bottom
of the dust tank and x them with screws.
2.Return dust tank assembly upright.
Remove / Change Used Dust Collection
Bag (Fig. A)
WARNING:
Appropriate personal protective
equipment like dust mask and gloves should be used
while handling used dust bags.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches
head .
4
3. Pull the collection bag carefully from inlet
4. Seal the collection bag opening tightly when removing
it from the machine.
5. Dispose of collection bag in appropriate container
according to statutory provisions.
Wet Pick Up Applications (Fig. A, G)
WARNING:
If foam or liquid escapes from the
machine,switch off immediately.
CAUTION:
Clean the water level limiting device
regularly and examine it for signs of damage.
Refer to Fig. G.
NOTICE:
DO NOT remove ball oat
will cause damage to the vacuum. The ball oat keeps
water from entering the motor.
Before using the vacuum for wet pick up:
• Ensure the canister is empty and free of excessive dust.
• Remove filters .
9
WARNING:
Do not use the machine with this set
up for dust Class L.
To Empty Canister (Fig. A, G)
The ball oat valve 14 will block air to the motor when
the canister is full and the sound of the motor will
change at once.
When the motor has a high pitched sound and air/
water ow stops, empty the canister.
1. Turn off vacuum and unplug cord from outlet.
2. Unlatch canister latches
head .
4
3. Empty contents of canister
container or drain.
To Convert Back to Dry Vacuum
Operation (Fig. A)
1. Empty Canister, refer to To Empty Canister
instructions.
15
WALT
E
and remove vacuum
5
.
10
14 , doing so
and remove vacuum
5
into a suitable
6