Triton T12ID Instrucciones De Uso Y De Seguridad página 8

Battery Charging Table
Charger plugged In
Charger evaluating battery
Fast charging
Highly discharged battery slow charging
Abnormal battery temperature charging
Fully Charged
Battery or charger fault
Temporary abnormal temperature
condition
NOTE: If the lights on the battery charger fail to illuminate according to the chart above or
indicate a fault condition:
• Check the battery is firmly seated in the battery charger
• Check all connections and that mains power is switched on
Initial charge
• The initial charge will vary depending on the existing charge in the battery. Allow the
battery to reach full charge as indicated on the charger
• After discharging, recharge the battery completely, as indicated by the LED on the battery
charger, for the next 4 to 5 uses. This will ensure that the battery is performing to its
highest capacity
• Subsequent full charges will take approximately 1 hour, however the battery can be
recharged when the battery is only partially discharged
Re-charging the battery
• After use, a lithium-ion battery must be allowed to cool down before charging
• If a hot battery is inserted into the charger both LEDs will illuminate. The charger will
begin to charge when the battery has cooled sufficiently (this may take several minutes)
Installing the battery
• The battery should fit easily into the battery charger or impact driver unit. If the battery is
difficult to fit, check the condition of the battery and contacts
Battery - length of service
The length of service from each charging cycle will depend on the type of workload. The
battery charger and battery for this drill have been designed to provide a long trouble-free
working life. The charger intelligently monitors the condition of the battery and selects the
ideal charging rate for the condition of the battery. It protects the battery from over-charging or
charging at too high a rate. However, like all batteries, performance will be reduced over time.
To maximise battery life:
• Store and charge the battery in a cool area. Temperatures above or below normal room
temperature will reduce battery life
• Never store lithium-ion batteries in a discharged condition. Recharge them immediately
after they are discharged. For storing long term, store fully charged
• All batteries gradually lose their charge, even lithium-ion batteries, but the discharge rate
is very low. If the drill is stored for long periods of time without use, recharge the battery
every three to four months and disconnect the battery from the power tool before it is
stored. This practice will prevent the lithium-ion battery being damaged when stored
Guarantee
To register your guarantee visit our web site at
www.tritontools.com* and enter your details.
Your details will be included on our mailing list (unless indicated otherwise) for
information on future releases. Details provided will not be made available to any third
party.
Purchase Record
Date of Purchase: ___ / ___ / ____
Model: T12ID Retain your receipt as proof of purchase
T12ID_Z1MANPRO1_US.indd 7
Red LED Green LED
OFF Flashing
OFF Flashing
ON Off
Flashing Off
Flashing Off
OFF On
Flashing Flashing
On On
art pr
Operating Instructions
NOTE: Make sure screwdriver bits used are hardened and suitable for use with an impact
driver.
Fitting a driver bit
1. Pull the Quick Release Mechanism (2) forward and insert the bit into the quick release ¼"
(6.35mm) Hex Drive (1)
2. Release the Quick Release Mechanism
3. Pull on the bit to check that it is securely fitted. If the bit is not secure, repeat the above
procedure
Direction control
• The direction of rotation can be set using the Forward/Reverse Selector (3)
• To rotate the impact driver clockwise, push the Forward/Reverse Selector to the left
• To rotate the impact driver anti-clockwise, push the Forward/Reverse Selector to the right
• When the Forward/Reverse Selector is in the central position, the impact driver is locked
• Do not attempt to move the Forward/Reverse Selector when the tool is running
Switching on
• To start the impact driver, squeeze the Trigger Switch (6). The LED Guide Light (7) will
illuminate automatically
• Further pressure on the Trigger Switch will increase the running speed of the tool
• Practise using the impact driver before using it for normal applications
NOTE: It is possible the impact driver may switch off during heavy use due to thermal
protection of the battery and internal components. This may prevent the tool being used again
for a short period of time and does not represent a fault
Maintenance
Cleaning
• Keep your machine clean at all times. Dirt and dust will cause internal parts to wear
quickly, and shorten the machine's service life. Clean the body of your machine with a
soft brush or dry cloth. If available, use clean, dry, compressed air to blow through the
ventilation holes
Storage
• Store this tool and accessories after use in its case (if supplied), or in a dry, secure place
out of the reach of children
Disposal
• Do not dispose of power tools, or other waste electrical and electronic equipment, with
household waste
• Contact your local waste disposal authority for information on the correct way to dispose
of
This tool is manufactured using class leading components and makes use of the latest in
intelligent circuitry that protects the tool and its components. In normal use it should provide
a long working life.
Name and address of the manufacturer:
Powerbox International Limited, Company No. 06897059. Registered address: Central
House, Church Street, Yeovil, Somerset BA20 1HH, United Kingdom.
Triton Precision Power Tools guarantees to the purchaser of this product that if any part
proves to be defective due to faulty materials or workmanship within 3 YEARS from the
date of original purchase,
Triton will repair, or at its discretion replace, the faulty part free of charge.
This guarantee does not apply to commercial use nor does it extend to normal wear and
tear or damage as a result of accident, abuse or misuse.
* Register online within 30 days.
Terms & conditions apply.
es to be defecti
This does not affect your statutory rights ov
GB
7
21/11/2014 10:50