Setting Up The Phone - Sony SPP-SS950 Manual De Instrucciones

INFORMATION FOR GENERAL
TELEPHONES
1. This equipment complies with Part 68 of the FCC rules. On the bottom of this
equipment is a label that contains, among other information, the FCC
registration number and ringer equivalence number (REN) for this
equipment. If requested, this information must be provided to the telephone
company.
2. The applicable registration jack (connector) USOC-RJ11C is used for this
equipment.
3. This equipment is designed to be connected to the telephone network or
premises wiring using a compatible modular jack which is Part 68 compliant.
The FCC compliant telephone cord and modular plug is provided with this
equipment.
4. The REN is used to determine the quantity of devices which may be
connected to the telephone line. Excessive RENs on the telephone line may
result in the devices not ringing in response to an incoming call. In most, but
not all areas, the sum of the REN's should not exceed five (5.0). To be certain
of the number of devices that may be connected to a line, as determined by
the total RENs, contact the local telephone company.
5. If your equipment (SPP-SS950) causes harm to the telephone network, the
telephone company will notify you in advance that temporary discontinuance
of service may be required. But if advance notice isn't practical, the telephone
company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is
necessary.
6. The telephone company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If
this happens the telephone company will provide advance notice in order for
you to make necessary modifications to maintain uninterrupted service.
7. If trouble is experienced with this equipment (SPP-SS950), for repair or
warranty information, please contact Sony Direct Response Center: Tel 1-800-
222-7669. If the equipment is causing harm to the telephone network, the
telephone company may request that you disconnect the equipment until the
problem is resolved.
8. All repairs will be performed by an authorized Sony service station.
9. This equipment cannot be used to party lines or coin lines.
10. This equipment is hearing aid compatible.
If your telephone is equipped with
automatic dialers
When programming emergency numbers and (or) making test calls to emergency
numbers:
1. Remain on the line and briefly explain to the dispatcher the reason for the
call.
2. Perform such activities in the off-peak hours, such as early morning or late
evenings.
Caution
You are cautioned that any changes or modifications not expressly approved in
this manual could void your authority to operate this equipment.
Note
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.

Setting up the phone

Choose the best location
Where you place the base unit affects the reception quality of the handset.
Place the base unit:
– near a central location and on a level surface
– away from television sets and other electronic equipment, a personal
computer, or a microwave oven
– away from noise sources such as a window by a street with heavy traffic
– away from another cordless telephone
– away from heat sources, such as radiators, airducts, and sunlight
– away from excessive moisture, extremely low temperatures, dust, mechanical
vibration, or shock
CAUTION
The cordless telephone operates at a frequency that may cause interference to
nearby TVs and VCRs; the base unit should not be placed near or on the top of a
TV or VCR; and, if interference is experienced, moving the cordless telephone
farther away from the TV or VCR will often reduce or eliminate the interference.
Connect the base unit
If you want to hang the base unit on the wall, see "Mounting the base unit on a
wall".
Hook
3
AC power adaptor
(supplied)
To AC outlet
Telephone line cord
2
(supplied)
To telephone outlet
1
Attach the wall bracket on the bottom of the base unit as illustrated
to use it as a stand. Align the ¢ marks of the wall bracket with those
of the base unit.
2
Connect the telephone line cord to the LINE jack and to a telephone
outlet.
3
Connect the AC power adaptor to the DC IN 9V jack and to an AC
outlet.
4
Raise the antenna. Make sure it points toward the ceiling.
Notes
• Use only the supplied AC-T37 AC power adaptor. Do
not use any other AC power adaptor.
• Connect the AC power adaptor to a continuous power
supply.
• Place the base unit close to the AC outlet so that you can
unplug the AC power adaptor easily.
Tips
• If your telephone outlet is not modular, contact your telephone
service company for assistance.
• To remove the wall bracket, press the upper tab.
Choose the dialing mode
For the telephone to work properly, select an appropriate dialing mode (tone or
pulse).
DIAL MODE switch
If you aren't sure of your dialing system
Make a trial call with the DIAL MODE switch set to T. If the call connects, leave
the switch as is; otherwise, set to P.
4
To DC
1
IN 9V
2
1
To LINE
Polarity of the plug
Modular
Depending on your dialing system, set
the DIAL MODE switch as follows:
If your dialing system is Set the switch to
Tone T
Pulse P