Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
･ To avoid fire, electric shock, damage or malfunction to your equipment, do not
disassemble or remodel.
･ Immediately stop using the card if you notice smoke, strange smells or sounds, or if
liquid gets into the card.
To use a P2 card, a P2 card driver must be installed on your P2 series product.
For the latest information on drivers and supported models, visit the P2 Support
Desk at the web site below.
In Japanese: http://panasonic.biz/sav/
In English:
https://eww.pavc.panasonic.co.jp/pro-av/
Features
This memory card is suitable for use in
P2 series products, such as memory
card cameras/recorders, memory card
recorders, and memory card drives, and
that complies with the CardBus standard.
For the latest information on supported
models, visit the P2 Support Desk at the
above web site.
Supplied accessories
A
(b) 1 Cap (part number: VMG1632)
(c) 1 Case (part number: VFC4069)
Preparations
Install the card's driver software before
using this card in a memory card drive or
computer. Find out how to obtain the
driver software by referring to the
operating instructions for the memory card
camera/recorder, memory card recorder,
memory card drive, or other device.
Handling and storage
precautions
• To avoid fire, electric shock, damage
or malfunction to your equipment, do
not impact, bend, drop, or wet.
• After removing the card from equipment,
immediately attach the cap to it to
protect its terminals from dust and grime.
When storing the card or carrying it
around, keep it in its protective case.
• Do not leave the card where it may be
exposed to corrosive gases.
• While data is being read or written, do
not remove the card or turn off any
equipment using the card. Do not
remove the batteries from battery
operated equipment. These actions
can cause loss or corruption of the
data. If this does happen during
writing, read the instructions for the
equipment as it may be possible to
retrieve the data.
• Make backup copies of your data
wherever possible. Panasonic will not
accept responsibility for any data loss
or loss directly or indirectly caused by
data loss.
How to remove the card
from its case
A
1 Release the lock in area (a).
2 Open the case.
• While removing the card, hold the case
in the direction shown in the figure so
that the card will not fall onto the floor
or ground.
• To avoid damaging the case, do not
attempt to open it by holding area (a).
3 Remove the card.
• To remove only the card, slide it in
direction (d).
• To remove the card with the cap,
remove it in direction (e) while at the
same time pushing it in the cap direction.
Model
DVCPRO,
2-channel audio
AJ-P2C016RG
64 minutes
AJ-P2C032RG
128 minutes
･ The recording times shown are when recording a clip onto a memory card
continuously.
Parts and their functions B
(f) Serial number
(g) Write-protect switch
• Switch to "PROTECT" to prevent
writing to the card. Disengage to
enable writing.
• There are also operations you can
perform
on
memory
cameras/recorders and memory card
recorders that allow you to protect or
enable writing on the card after you
insert it. Read the instructions for the
equipment for details.
• Engage or disengage the switch
before inserting the card into a
memory card drive or computer.
• To prevent malfunction, ensure the
switch is correctly in position.
(h) Memo space (Reverse side)
• Use an oil-based felt pen to write in the
memo space. Erase with a lens
cleaner (the HyperClean EE series
from Olympus is recommended).
Be absolutely sure to check the felt
pen before using it since what is
written by some of these pens cannot
be completely erased.
• Do not use pencil or ballpoint pen as
these can damage the card.
• Do not detach the label on the card or
attach other labels or stickers as these
can cause malfunction.
(i) Serial number bar code (Reverse
side)
The serial number is displayed with the
following specifications.
• Type:
CODE128
• Narrow width: 0.18 mm
For further details, see the Operating
Instructions for your bar code reader.
(j) Case pocket
You can put a notepad in this pocket.
Specifications
Interface: CardBus (PC card standard)
Capacity:
AJ-P2C016RG: approx. 16 GB
AJ-P2C032RG: approx. 32 GB
Recording times: See below
Input voltage: DC 3.3 V ±0.3 V
Power consumption: approx. 1.5 W
Operating temperature: –20 °C to +60 °C
(–4 °F to +140 °F)
Operating humidity:
5 % to 90 % (no condensation)
Storage temperature: –40 °C to +80 °C
(–40 °F to +176 °F)
Storage humidity:
5 % to 90 % (no condensation)
Dimensions (mm):
85.6 (L) X 54 (W) X 5 (D)
(inches: 3.37 (L) X 2.13 (W) X 0.2 (D))
Mass: 45 g (1.6 oz)
• Total card capacity includes space for
data management such as system
data, therefore, actual usable area is
less than capacity indicated on the
card.
• Specifications are subject to change
without notice.
• Mass and dimensions are approximate.
Recording times (approx.)
DVCPRO50,
DVCPROHD,
4-channel audio
8-channel audio
32 minutes
16 minutes
64 minutes
32 minutes
A
1
2
card
3
(c)
B
(e)
(b)
( f ) ( g )
( i )
( h )
( j )
(a)
(d)
Publicidad
