Technical Data - Rockwell JAWSTAND XP Manual De Instrucciones

Portable Work SuPPort

teChNiCal data

Max clamp width
Max. load
height adjustment range
using macro-height locking knob
using precise height adjustment handle
Bevel adjustment range
folded minimum length
Weight
oPeratiNG iNStruCtioNS
Note: Before using the jaWsTaNd xP
this instruction book carefully.
aSSeMblY
uNPaCkiNG
This product requires some assembly.
Carefully remove the jaWsTaNd xP
head and the column of the tool are separated from the
tripod base. (see fig. a1) first loosen the height locking
knob (9). Then insert the column of the tool into the
base and tighten the knob.(see fig. a2). after inserting
the column into the base, use a pair of pliers to bend out
the metal tab (found at the base of the column). This
will prevent the column from slipping out of the base.
(see fig. a3) assemble the included precise height
adjustment handle (15) onto the pinion shaft and tighten
the screw. (see fig. a4)
inspect carefully to make sure no damage occurred
during shipping.
do not discard the packing material until you have
carefully inspected and satisfactorily operated the tool.
2. Set-uP iNStruCtioNS
1. unfold the tripod legs of the main body and extend
the column upwards to the desired height (there is a
limit stop). (see fig. B1 & B2)
Note: The legs should pivot smoothly but firmly. adjust
the pivot bolts (a) on the leg if necessary. (see fig. B3)
2. Loosen the bevel locking knob(4) and rotate the
bevel head(3) until the low friction slides (1) are
horizontal then tighten the height locking knob(9)
as shown in fig. C1&C2. Make sure the head locks
firmly. adjust the tension on the pivot bolt (b) if
necessary.(see fig. d) The head should pivot firmly,
and should lock tightly at any selected angle when
the bevel locking knob is tightened.
10
1-3/4˝
220 lbs
29˝ -41˝
0˝-2˝
0-90
0
43˝
15.3 lbs
, read
TM
from the box. The
TM
adjuStMeNt aNd oPeratioN:
Make sure the legs are fully opened, and that both
the height clamp and the bevel locking knob are fully
tightened before applying heavy loads.
• Do not overload. Max. load per jaWsTaNd xP
220 lbs (100 kg).
• Do not stand on this product.
1. adjuSt SuPPort heiGht(29˝-43˝)
(1) using macro-height locking knob(9) (29˝-41˝):
The scales on the column indicate the slide height above
the ground. To adjust the height, loosen the height
locking knob and slide the head upward or downward.
Read the scale from the top edge of the base. (see fig.
E1 & E2)
Note: Only when the precise height adjustment column
is in 0 position is the number on the lower column
the same as the actual height. in order to calculate
the height after raising the jaWsTaNd xP
precise height adjustment handle, you must add the
measurement on the precise height adjustment column
to the measurement on the column below the precise
height adjustment knob.
(2) using the precise height adjustment handle(15)
(0˝-2˝):
The precise height adjustment knob allows you to raise
or lower the jaWsTaNd xP
height that is needed. Rotate the knob clockwise to
raise the head or counterclockwise to lower. (see fig.
E3 & E4)
Note: do not try to force the handle past the minimum
and maximum positions of the jaWsTaNd xP
or else it will cause damage to the machine.
2. ClaMPiNG
Rotate the clamp handle. The moving clamp (13) will
move forward or backward for clamping or loosening
work-piece against the fixed pads (14). (see fig. f1, f2
& f3). Then press down the handle to lock the work-
piece.
• When clamping materials less than 3/4˝ (20mm) thick,
use a spacer. (see fig. G)
• When hanging doors, rotate the bevel head from 0° to
90°. Tighten the clamp handle to clamp the door side,
and put a spacer block under the door to support the
hinge line.
eNG
TM
with the
TM
to the exact working
TM
's height
TM
is