Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
PermaWrap
Craftsman Installation Instructions
®
1. Measure the opening height to
determine the overall length of the
column. Cut the column 1/8" shorter
than your measurement. CUT THE
COLUMN FROM THE BOTTOM to the
desired length with a circular saw
with a fine-tooth carbide blade. DO
NOT CUT COLUMN FROM THE TOP!
2. Place the L-shaped column half
containing the two nailing cleats in
position around the structural post.
Nailing
Cleats
3. Apply a continuous 1⁄4" bead of
Siroflex adhesive caulk (included)
along both mitered edges of the
column half.
4. Place second L-shaped column half
in place, around the structural post
and slide the two mitered column
halves together.
5. Use a pneumatic finish nailer or fin-
ish stapler and fasten the two column
halves together every 6"-8", along
both edges of the column where the
2 L-shaped column halves come to-
gether. Fasten through the face of the
column into the nailing cleat. NOTE:
Clean off any caulk squeeze-out
with a clean, damp rag.
6. Install the 4 L-shaped column
mounting brackets. 2 brackets attach
the top of the column to a beam, &
2 attach the column to the bottom
mounting surface. The 2 pairs of
brackets should be attached to oppo-
site sides of the column. NOTE: The
two brackets attached to the beam
should be installed on the 2 faces of
the column that are perpendicular to
the direction of the beam.
First, use the blue screws to attach
the brackets to the bottom mount-
ing surface, & to the beam resting
directly on top of the column. If the
floor surface is concrete or masonry,
use a 3/16" masonry drill bit to drill
the screw attachment holes. Drill the
holes at least 2-1/4" deep. Clean all
debris from holes. Drill 1/8" diameter
holes for screws being fastened to a
wooden surface.
7. After attaching the column mount-
ing brackets to the mounting surfac-
es, use the silver screws to attach
the brackets to the column shaft. Drill
1/8" diameter holes for screws being
fastened to the column shaft.
CRAFTSMAN 1
PERMAWRAP
®
Publicidad
Resumen de contenidos para HB&G Building Products PermaWrap Craftsman
- Página 1 PermaWrap Craftsman Installation Instructions ® 1. Measure the opening height to 4. Place second L-shaped column half First, use the blue screws to attach determine the overall length of the in place, around the structural post the brackets to the bottom mount- column.
- Página 2 COLUMN SHAFT READY FOR CAP AND COLUMN AFTER CAP AND BASE YOUR COLUMN IS COMPLETE BASE MOULDING INSTALLATION MOULDING INSTALLATION 8. Fit the cap and base moulding around the column. If you have 9. If you want to use the included cut the bottom of the column shaft neck moulding, fit the neck moulding shorter, you will need to trim the base...
- Página 3 TOOLS NEEDED FOR PVC CRAFTSMAN COLUMN INSTALLATION Necessary Circular Saw / Skilsaw Cut column shaft to length Necessary Power Miter Box Re-cut base trim when column shaft has been cut shorter Necessary Pneumatic Trim Nailer / Trim Stapler Fasten column shaft together, fasten cap and base together, attach cap & base to column shaft, attach blocking to structural post, attach column shaft to blocking.
- Página 4 HB&G PVC Column Painting Instructions PermaWrap , RigidWrap & PermaSnap ® ® 1. A high quality acrylic exterior paint should be used to finish your PVC columns. At least one coat of primer and two coats of the final paint should be used.
- Página 5 Instrucciones de instalación de PermaWrap Craftsman ® 1. Mida la altura de apertura para determinar 4. Coloque la segunda mitad de la columna Primero, use los tornillos azules para fijar los la longitud total de la columna. Corte la co- en forma de L en su lugar, alrededor del poste soportes a la superficie de montaje inferior lumna 1/8 ”más corta que su medida.
- Página 6 EJE DE COLUMNA LISTO PARA LA SU COLUMNA ES COMPLETA COLUMNA DESPUÉS DE LA INSTALACIÓN DE INSTALACIÓN DE TAPA Y MOLDEADO BASE TAPA Y MOLDEADO BASE 8. Coloque la tapa y la moldura de base alrededor de la columna. Si ha cortado la 9.
- Página 7 HERRAMIENTAS NECESARIAS PARA LA INSTALACIÓN Utilizar DE COLUMNA DE PVC CRAFTSMAN Necesaria Sierra circular / sierra circular Corte el eje de la columna a la longitud Necesaria Power Mitre Box Recorte el recorte de la base cuando el eje de la columna se haya cortado más corto Necesaria Grapadora neumática de recorte / grapadora...
- Página 8 • CORTE Y FIJACIÓN: el material de PVC celular con el que están construidas las columnas se puede cortar fácilmente con herramientas convencionales de carpintería y carpintería. Las clavadoras y engrapadoras de acabado neumático se pueden utilizar para sujetar piezas de PVC celular.