Black and Decker 9073 Manual De Instrucciones

9 9 0 0 7 7 3 3 C C O O R R D D L L E E S S S S 2 2 . . 4 4 V V
9 9 0 0 7 7 3 3 C C O O R R D D L L E E S S S S 2 2 . . 4 4
INSTRUCTION MANUAL
T
T
HANK YOU FOR CHOOSING
HANK YOU FOR CHOOSING
G .B
G .B
O T O WWW LACKAND
O T O WWW LACKAND
T O REGISTER
T O REGISTER
BEFORE RETURNING THIS PRODUCT
FOR ANY REASON PLEASE CALL
1-800-544-6986
BEFORE YOU CALL, HAVE THE CATALOG No. AND DATE CODE AVAILABLE. IN MOST CASES, A
BLACK & DECKER REPRESENTATIVE CAN RESOLVE THE PROBLEM OVER THE PHONE. IF YOU HAVE A
SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO BLACK & DECKER.
KEY INFORMATION YOU SHOULD KNOW:
TO CHARGE: Charge 12 hours before first use.
TO OPERATE: The black button must be in the forward/reverse position
and depressed to operate tool in either direction. When the button is in
the center, it is in a safety position and will not operate.
TO INSTALL A BIT : Insert bit firmly into the cavity in the spindle until it
snaps into place. If the bit does not fit into the spindle, rotate the bit and
re-insert it.
SAVE THIS MANUAL FOR FUTURE REFERENCE.
VEA EL ESPAÑOL EN LA CONTRAPORTADA.
INSTRUCTIVO DE OPERACIÓN, CENTROS DE SERVICIO Y PÓLIZA DE
GARANTÍA. ADVERTENCIA: LÉASE ESTE INSTRUCTIVO ANTES DE USAR EL
PRODUCTO.
C C a a t t N N o o . . 9 9 0 0 7 7 3 3 F F o o r r m m N N o o . . 6 6 0 0 4 4 3 3 6 6 9 9 - - 0 0 0 0 R R E E V V . . 1 1
GENERAL SAFETY RULES - FOR ALL BATTERY OPERATED TOOLS
WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in electric shock, fire and/or serious
personal injury.
SAVE THESE INSTRUCTIONS
Work Area
• Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents.
• Do not operate power tools in explosive atmospheres, such as in the presence of
flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
fumes.
• Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control.
Electrical Safety
• A battery operated tool with integral batteries or a separate battery pack must be
recharged only with the specified charger for the battery. A charger that may be suitable
for one type of battery may create a risk of fire when used with another battery.
• Use battery operated tool only with specifically designated battery pack. Use of any
other batteries may create a risk of fire.
Personal Safety
• Stay alert, watch what you are doing and use common sense when operating a power
tool. Do not use tool while tired or under the influence of drugs, alcohol, or
medication. A moment of inattention while operating power tools may result in serious
personal injury,
• Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your
hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair
can be caught in moving parts.
• Avoid accidental starting. Be sure switch is in the locked or off position before
inserting battery pack. Carrying tools with your finger on the switch or inserting the battery
pack into a tool with the switch on invites accidents.
• Remove adjusting keys or wrenches before turning the tool on. A wrench or a key that is
left attached to a rotating part of the tool may result in personal injury.
• Do not overreach. Keep proper footing and balance at all times. Proper footing and
balance enable better control of the tool in unexpected situations.
• Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes,
hard hat, or hearing protection must be used for appropriate conditions.
Tool Use and Care
• Use clamps or other practical way to secure and support the workpiece to a stable
platform. Holding the work by hand or against your body is unstable and may lead to loss of
control.
• Do not force tool. Use the correct tool for your application. The correct tool will do the
job better and safer at the rate for which it is designed.
• Do not use tool if switch does not turn it on or off. A tool that cannot be controlled with the
switch is dangerous and must be repaired.
• Disconnect battery pack from tool or place the switch in the locked or off position
before making any adjustments, changing accessories, or storing the tool. Such
preventive safety measures reduce the risk of starting the tool accidentally.
• Store idle tools out of reach of children and other untrained persons. Tools are
dangerous in the hands of untrained users.
• When battery pack is not in use, keep it away from other metal objects like: paper
clips, coins, keys, nails, screws or other small metal objects that can make a
O O L L T T 3 3 P P O O S S I I T T I I O O N N S S C C R R E E
V V O O L L T T 3 3 P P O O S S I I T T I I O O N N S S C C R R E E
B & D
B & D
LACK ECKER
LACK ECKER
D . /N O
D . /N O
ECKER COM EW
ECKER COM EW
.
.
YOUR NEW PRODUCT
YOUR NEW PRODUCT
( ( J J U U L L Y Y ' ' 0 0 6 6 ) ) C C o o p p y y r r i i g g h h t t © © 2 2 0 0 0 0 6 6 B B l l a a c c k k & & D D e e c c k k e e r r
connection from one terminal to another. Shorting the battery terminals together may
cause sparks, burns, or a fire.
• Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools,
with sharp cutting edge are less likely to bind and are easier to control.
• Check for misalignment or binding of moving parts, breakage of parts, and any other
condition that may affect the tool's operation. If damaged, have the tool serviced
W W D D R R I I V V E E R R
W W D D R R I I V V E E R R
before using. Many accidents are caused by poorly maintained tools.
• Use only accessories that are recommended by the manufacturer for your model.
Accessories that may be suitable for one tool may create a risk of injury when used on
another tool.
Service
• Tool service must be performed only by qualified repair personnel. Service or
maintenance performed by unqualified personnel may result in a risk of injury.
• When servicing a tool, use only identical replacement parts. Follow instructions in the
!
!
Maintenance section of this manual. Use of unauthorized parts or failure to follow
Maintenance Instructions may create a risk of shock or injury.
WNER
WNER
SPECIFIC SAFETY RULES
• Hold tool by insulated gripping surfaces when performing an operation where the
cutting tool may contact hidden wiring. Contact with a "live" wire will also make exposed
metal parts of the tool "live" and shock the operator.
The label on your tool may include the following symbols.
V ..........................volts
Hz ........................hertz
min ........................minutes
......................direct current
.......................... Class II Construction
........................safety alert symbol
WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other con-
struction activities contains chemicals known to cause cancer, birth defects or other repro-
ductive harm. Some examples of these chemicals are:
• lead from lead-based paints,
• crystalline silica from bricks and cement and other masonry products, and
• arsenic and chromium from chemically-treated lumber. (CCA)
Your risk from these exposures varies, depending on how often you do this type of work. To
reduce your exposure to these chemicals: work in a well ventilated area, and work with
approved safety equipment, such as those dust masks that are specially designed to filter out
microscopic particles.
A
3
C
11 10
P P r r i i n n t t e e d d i i n n C C h h i i n n a a
9
F
FEATURES (FIGURE A)
1. On/off switch with forward/reverse function
2. Spindle lock collar
3. Bit holder
4. Handle adjustment button
5. Handle
6. Battery cover
CHARGING THE SCREWDRIVER
Before attempting to charge your screwdriver, thoroughly read all of the safety instructions.
To charge your screwdriver, follow the steps below.
1. Plug the output cord of the charger (7) into the socket in the back half of the screwdriver
handle (8) as shown in Figure B.
2. Plug the charger into any standard electrical outlet.
CHARGING NOTES
NOTE: The tool was sent from the factory in an uncharged condition. Before attempting to
use it, it must be charged for 12 hours.
1. Charger will work best at normal room temperature.
2. The charger plug and the tool handle may become warm while charging. This is normal
and does not indicate a problem.
3. The tool can be left on charge as long as you desire. A minimum charge time of 12 hours
is required to recharge a completely discharged tool.
4. For most fix up jobs a charge of 3 to 4 hours will be adequate.
WARNING: When disconnecting the screwdriver from the charger, be sure to unplug the
charger from the outlet first then disconnect the charger cord from the screwdriver.
Operating Instructions
REMOVING AND INSTALLING BITS
To install a screwdriver bit (9) Fig. C simply insert it into the cavity in the spindle (2) until it
snaps into place. To remove the bit pull it straight out. If bit does not fit into spindle, rotate the
bit and re-insert it. To insert a bit tip (11) first insert a bit tip holder (10) into the spindle and
then insert the bit tip into the holder. NOTE: Screwdriver bit types and quantity may vary.
ADJUSTING THE HANDLE
For optimum versatility, the handle can be be set to different positions as shown in Fig. D. To
adjust the handle, press the handle adjustment button (4) and swivel the handle into the
desired position. Release the button and the handle will lock in that position. NOTE: To avoid
being pinched, grasp the handle below the pinch point shown in Figure D.
OPERATING IN POWER MODE
Forward
• Rotate the collar shown in Fig.E to the position marked POWER.
• Slide the button shown in Fig.F to the right, exposing the triangle pointing forward.
• Press the button and the tool will run; release the button and the tool will stop.
Reverse
• Rotate the collar shown in Fig. E to the position marked POWER.
• Slide the button shown in Fig. F to the left, exposing the triangle pointing backward.
1
2 4 5 6
D
Pinch Point
Point de pincement
Punto de pellizco
R
L
1
A..........................amperes
W ........................watts
......................alternating current
n o ........................no load speed
........................ earthing terminal
.../min ..................revolutions or
reciprocations
per minute
B
8
7
E
4
2