Maintenance And Storage - LUND 67112 Manual Original

GB
adapter bracket onto the housing and then mount the accessories on the adapter (XII).
Installation of accessories
Insert the selected accessory into the opening in the dust container housing (XIII).
Accessories equipped with a rectangular outlet are fi xed directly into the dust container opening. Accessories equipped with a
round outlet are fi xed using the adapter.
Purpose of the accessories
Floor and carpet brush - universal brush for cleaning both carpets and all types of hard fl oors.
Turbo brush - universal brush for cleaning both carpets and all types of hard fl oors. Thanks to the additional shaft it is possible to
clean more eff ectively than with a regular brush.
Small brush - universal brush designed for cleaning areas inaccessible for normal size brushes. Recommended for cleaning
furniture with upholstery.
Bristle brush - a brush designed to clean hard, small-size surfaces.
Crevice attachment - enables cleaning places which are diffi cult to access, e.g. inside radiators.
Set of narrow suction attachments - for precise and effi cient cleaning of small areas. Fixed by means of a fl exible hose, makes
the use of suction attachments much easier.
Using the device
Insert the power cord into the slot of the handle hook pointing downwards (XIV). This will increase the distance between the power
cord and the brush, reducing the risk of the power cord being caught by the brush.
After installing the dust container and the selected accessories, make sure that the switch is in the "off " position - O, plug the power
cord plug into the socket. Turn the vacuum cleaner on by moving the switch to the "on" position - I, and start cleaning.
The device is switched off when the switch is set to the "off " position - O.
Control the amount of impurities in the container during operation. Place the container vertically with the lid downwards and check
the amount of impurities. Empty the container if the impurities level in the container is equal to the edge of the external fi lter (XV).

MAINTENANCE AND STORAGE

CAUTION! Never immerse the vacuum cleaner in water or other liquids. Doing so may result in electric shock.
After cleaning, turn off the vacuum cleaner with the switch, disconnect the power cord plug from the socket, disconnect the ac-
cessories and proceed with maintenance.
Disconnect the dust container from the vacuum cleaner. Open the lower cover of the container and discharge the waste collected in the
container. Open the top cover, remove both fi lters. Clean the container with a damp, soft cloth, then dry with a dry cloth or allow to dry.
Warning! It is forbidden to use the vacuum cleaner with a wet or damp fi lter. This can result in electric shock.
The plastic fi lter can be rinsed under running, lukewarm water. Next dry with a dry cloth and allow to dry completely. Wait at least
24 hours after placing the fi lter in a well-ventilated place at room temperature.
Do not wash fi lters in mechanical dishwashers and do not dry them with a stream of hot air. This can cause deformation of the
plastic material used for the construction of the fi lter. Avoid exposing the fi lters to direct sunlight.
No other part of the vacuum cleaner must be exposed to water. Gently tap the internal fi lter to shake off larger impurities. In the
case of excessive contamination, replace the fi lter with a new one.
Clean the remaining parts of the vacuum cleaner with a cloth slightly soaked in water, then dry or allow to dry.
Clean the turbo brush shaft by removing the transparent cover. Grasp the cover at the bottom and lift it so that the cover latches
are released (XVI). Clean the shaft with a brush and then reattach the cover. The shaft is driven by a turbine located under the
cover on the underside of the brush. If a decrease in shaft speed is observed, clean the turbine. Remove the turbine cover by
grasping both latches at the same time and pulling them together (XVI). Clean the turbine with a brush and then fi x the cover. If
the cover is not installed, the turbine will not rotate.
The vacuum cleaner can be stored in a vertical position, resting on the fl oor and carpet brush or on the turbo brush. In this position,
the vacuum cleaner should stand without support. By turning the handle hook upwards, you can use this hook together with the
drive housing hook to retract the power cord (XVII). The accessories can be connected or disconnected from the vacuum cleaner
for storage. Store the vacuum cleaner with the power cord's plug disconnected from the socket.
O R I G I N A L I N S T R U C T I O N S
14