Safety Instructions - YATO YT-85330 Manual Original

Lifting height [m]
13
14
15
16
17
Caution! The maximum pump capacity pertains to pumping clean water. To ensure maximum capacity, a hose with a diameter
corresponding to the maximum water connector diameter must be connected to the pump.

SAFETY INSTRUCTIONS

CAUTION! Read all of the following instructions. Failure to do so may result in electric shock, fi re, or personal injury.
FOLLOW THE INSTRUCTIONS BELOW
Instructions for use
The device is intended only for pumping clean or slightly mechanically polluted water. Mechanical impurities must not be abrasive
and the size of individual particles must not exceed the size given in the technical data table. The device is not designed to pump
liquids other than water, such as oils, petrol, solvents, acids, bases, organic substances, fats, sewage, faecal matter, as well as
water contaminated with such substances. The appliance must be kept under supervision at all times during operation. Do not
allow the pump to operate dry. This will cause the pump to overheat, which can damage it and cause fi re or electrical shock.
The pump must not be used: for pumping drinking water; for continuous operation, for example, for supplying a fountain with
water; for pumping water at a temperature higher than that specifi ed in the technical data table.
It is forbidden to repair, disassemble or modify the appliance on one's own. All repairs to the product must be carried out by an
authorised service centre.
Clean the pump only with a clean water jet.
The appliance is not intended for use by children under at least 8 years of age and by persons with reduced physical and/or mental
abilities and by persons without experience in or understanding of the operation of the appliance. Unless they will be supervised or
instructed to use the appliance safely, in a manner ensuring that the risks involved are understood. Children should not play with
the appliance. Unattended children should not be allowed to perform the cleaning and maintenance of the appliance.
Recommendations concerning transport and installation of the appliance
Warning! The pump must not be connected to the power supply during submersion. The pump power cord must be unplugged
from the socket.
The pump sucks the water through openings in the base. The pump should be submerged in water with the cord attached to the
handle on the top of the pump housing before submersion. Do not use the power cord to submerge the pump. The power cord
must not be overly tensioned.
If the pump is lowered into a water tank whose bottom is contaminated with e.g. sand or sludge, or the water tank does not have a
hard bottom, ensure that the pump is not lowered all the way to the bottom. The impurity suction pump will then work less effi cient-
ly. In addition, contamination will lead to faster wear of the pump. Excessive contamination can lead to blockages in the pump's
inlet openings, which can cause damage to the pump.
It is forbidden to immerse the pump in water bodies with people in them.
If the pump is submerged in water bodies with a small surface area, e.g. a well, the minimum dimensions of the tank at the pump's
workplace are given in the technical data table.
The submerged pump must be positioned vertically. Tipping or tilting the pump leads to malfunction, reduces performance, and
can also result in damage to the pump.
It is forbidden to drill any holes in the device, as well as making any other modifi cations of the device not described in the manual.
Move the product by grasping the handle or housing. Do not move the device by pulling on the power cord.
Recommendations for connecting the appliance to the power supply
Warning! The pump shall be supplied by a residual current device (RCD) with a rated diff erential current of not more than 30 mA.
Before connecting the appliance to the power supply, make sure that the voltage, frequency and performance of the power supply
corresponds to the values shown on the appliance's rating plate. The plug must fi t into the outlet. It is forbidden to modify the plug
in any way.
The power supply circuit must be fi tted with a protective conductor and at least a 16 A protective device.
Avoid contact of the power cord with sharp edges, hot objects or surfaces. During operation, the power cord must always be fully
extended and the position of the power cord must be set so that it does not become an obstacle during operation. The power cord
O R I G I N A L
Catalogue No. Catalogue No.
YT-85330 YT-85333
Capacity [l/h] Capacity [l/h]
-
-
-
-
-
I N S T R U C T I O N S
GB
Catalogue No.
YT-85341
Capacity [l/h]
3,000 3,000
2,000 2,000
1,000 1,000
- -
- -
Catalogue No.
YT-85343
Capacity [l/h]
5,000
4,000
3,000
2,000
1,000
11