Publicidad
Idiomas disponibles
Idiomas disponibles
All manuals and user guides at all-guides.com
wet rag, that is then washed.
•
A special dust mask or respirator should be worn by all
people entering the work area. Be sure the mask fits. Change
filters often. Disposable paper masks are not adequate.
•
Children, pregnant or potentially pregnant women and
nursing mothers should not be present in the work area until
the work is done and all cleanup is complete.
•
No eating, drinking, gum chewing or smoking should be
done in the work area to prevent ingesting contaminated paint
particles. Workers should wash and clean up before eating,
drinking or smoking.
•
Clean up all removed paint and dust by wet mopping the
floors. Use a wet cloth to clean all walls, sills and any other
surfaces where paint or dust is clinging.
•
At the end of each work session dispose of the paint chips
properly.
Unpacking
When unpacking, check to make sure that all components are
included. Refer to the drawings on this manual. If any parts are
missing or broken, please call IVT assistance center.
Dust extraction
Dust extraction prevents large accumulations of
dust, high concentrations of dust in the ambient
air, and facilitates disposal.
It is necessary to connect the dust box assembly (6) to the
device, to collect the dust.
Installing the dust box assembly (6)
WARNING
Always unplug the device from the power source before
installing, cleaning or removing the dust box assembly (6).
1.
Insert the dust box assembly (6) into the dust extraction
connection (5). [F1]
NOTE: Make sure the tabs of the dust box assembly (6) insert
into the matching slots in the dust extraction connection (5).
2.
Rotate the dust box assembly (6) clockwise approximately
15° to lock it into place.
Removing and cleaning the dust box assembly (6)
The dust box assembly (6) should be removed periodically and
emptied to prevent excessive dust build up and to maintain its
effectiveness.
1.
Remove the dust box assembly (6) from the dust extraction
connection (5) by rotating it counter clockwise approximately
15° and pulling it out of the dust extraction connection (5).
2.
Carefully shake the dust box assembly (6) with the
opening pointing downward to remove the sanding dust.
NOTE: It is best to perform this function outdoors over a trash
can to prevent sanding dust from escaping into the work
area.
3.
Once the sanding dust is removed from the dust box
assembly (6), reinstall the dust box assembly (6).
Fitting sandpaper sheets
Sandpaper selection
Selecting the correct grit and type of sandpaper is extremely
important in achieving a high quality sanded finish.
Aluminum oxide, silicon carbide and other synthetic abrasives
are best for power sanding. Natural abrasives such as flint
and garnet are too soft for economical use in power sanding.
In general, coarse grit will remove the most material and finer
grit will produce the best finish in all sanding operations.
If the surface to be sanded is rough, start with a coarse grit and
sand until the surface is uniform. Medium grit may then be used
to remove scratches left by the coarser grit. Fine grit should be
used for finishing the surface.
Always continue sanding with each grit until the surface is
uniform.
Installing sandpaper sheets
WARNING
Use only sandpaper that is recommended for this device.
The use of improper accessories may result in injury to the
operator or damage to the tool.
WARNING
Always unplug the device from the power source before
installing or changing sandpaper.
1.
Lift up and outward on the front and rear sandpaper clamp
ing levers (3) at the front and rear of the sanding pad (2) [F2].
2.
Insert one end of the sandpaper sheet (with grit side up)
into the open front sandpaper clamp (4), making sure it is
aligned with the sanding pad (2).
3.
Lift the sandpaper clamping lever (3) up and inward to lock
the sandpaper into the sandpaper clamp (4).
4.
Wrap the sandpaper sheet over the sanding pad (2) and
insert it into the open rear sandpaper clamp (4) [F3].
NOTE: Make sure the sandpaper is pulled tight over the
sanding pad (2) for proper sanding operation.
5.
Lift the sandpaper clamping lever (3) up and inward to lock
the sandpaper into the sandpaper clamp (4).
ATTENTION
For a proper functioning of the dust extraction system, dust
extractor holes on sandpaper sheet and sanding pad (2) must
correspond.
15
Instruction manual
EN
Publicidad
