Intended Use; Safety Instructions - nedis HTBA10GY Guia De Inicio Rapido

a
Quick start guide
Bathroom heater
For more information see the extended manual online:
ned.is/htba10gy

Intended use

This product is a heater that allows the user to control the
surrounding temperature in the bathroom.
This product is intended for indoor use only.
This product is only suitable for well insulated spaces or occasional
use.
This product can be used by children aged from 8 years and above
and persons with reduced physical, sensory or mental capabilities
or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the product in a safe
way and understand the hazards involved.
Children of less than 3 years should be kept away unless
continuously supervised.
Children aged from 3 years and less than 8 years shall only switch
on/off the product provided that it has been placed or installed in
its intended normal operating position and they have been given
supervision or instruction concerning use of the product in a safe
way and understand the hazards involved. Children aged from 3
years and less than 8 years shall not plug in, regulate and clean the
product or perform user maintenance.
Children shall not play with the product.
The product is intended for use in household environments for
typical housekeeping functions that may also be used by non-expert
users for typical housekeeping functions, such as: shops, offices
other similar working environments, farm houses, by clients in
hotels, motels and other residential type environments and/or in
bed and breakfast type environments.
This product is not suitable for primary heating purposes.
Any modification of the product may have consequences for safety,
warranty and proper functioning.
Specifications
Product
Article number
Dimensions (d x w x h)
Input power
Rating power
Waterproof
Cable length
Main parts (image A)
Bathroom heater
1
2 Wall mount
3 Mounting hole
Wall mount lid
4
Power cable
5

Safety instructions

Icon Description
To avoid overheating, do not cover the product.
HTBA10GY
Bathroom Heater
HTBA10GY
100 x 560 x 160 mm
220-240 V ~ 50 Hz
1000 - 1200 W
IPX4
1.4 m
Screws (2x)
6
7 Plugs (2x)
8 Mode indicator
Pull cord
9
Indication for a hot surface. Contact may cause
burns. Do not touch.
-
WARNING
• Ensure you have fully read and understood the instructions in
this document before you install or use the product. Keep the
packaging and this document for future reference.
• Only use the product as described in this document.
• Do not use the product if a part is damaged or defective. Replace
a damaged or defective product immediately.
• Do not drop the product and avoid bumping.
• This product may only be serviced by a qualified technician for
maintenance to reduce the risk of electric shock.
• Do not use this heater in the immediate surroundings of a bath, a
shower or swimming pool.
• Do not locate the product immediately below a power outlet.
• Unplug the product from the power source and other equipment
if problems occur.
• Always use the voltage (A.C. Only) marked on the rating label.
• Before cleaning and maintenance, switch off the product and
disconnect the product from the power source.
• Close supervision is necessary when the product is used by or
near children, animals or infirm persons.
• Do not use the product near explosive or flammable materials.
• Always unwind the power cable before using the product.
• Do not let the power cable touch hot surfaces.
• Only use the product in the upright position.
• Keep the air inlet grill clean.
• The power cable cannot be replaced. If the cable is damaged the
product should be scrapped.
• Disconnect the product from the power source before service
and when replacing parts.
Bathroom zones (image B)
Never use the product while taking a shower or bath. This might
4
cause an electric shock.
Bathroom
0 The area inside the
bath.
1 The area is the same
width as zone 0 (the
width of the bath)
extending to 2.25 m
above the finished
floor level.
2 The area is the same
height as zone 1 (2.25
m), extended to 0.6 m
around the bath.
3 Remaining space
Installing the product (image C + D)
Only install the product in zone 3, at least 1.8 m above the
4
ground and 30 cm below the ceiling.
1. Drill holes with a diameter of 8 mm and place the plugs A
2. Remove the wall mount lid A
The bathroom heater A
4
3. Rotate A 1 for better access to the mounting holes A
5
Shower room Suitability
The area inside the Not suitable
shower basin.
The area is 2.25 m Not suitable
from the finished
floor level or the
height of the fixed
shower head.
The area is the same Not suitable
height as zone 1,
extended to 0.6 m
around the shower
basin.
Remaining space Suitable
from the wall mount A
4
1 can now rotate further than 40°.
.
7
2 .
3 .