Low-Battery Indicator - Black and Decker BDCOS18 Traducido De Las Instrucciones Originales

Re-insert the battery (4).
u
If the charging indicators continues flashing red at a fast
u
rate, use a different battery to determine if the charging
process works properly.
If the replaced battery charges correctly, the original
u
battery is defective and should be returned to a service
centre for recycling.
If the new battery gives the same indication as the original
u
battery, take the charger to be tested at an authorised
services centre.
Note: It may take as long as 30 minutes to determine that
the battery is defective. If the battery is too hot or too
cold, the LED will alternately blink red, fast and slow, one
flash at each speed and repeat.
Fitting and removing the battery (fig. B)
To fit the battery (4), line it up with the receptacle on the
u
tool. Slide the battery into the receptacle and push until
the battery snaps into place.
To remove the battery, push the release buttons (4a) while
u
at the same time pulling the battery out of the receptacle.
Fitting and removing the accessories (fig. C–G)
Warning! Before fitting an accessory, disconnect the tool from
the mains supply/Remove battery from tool.
Fitting a BLACK+DECKER accessory (fig. C-F)
Hold the tool and squeeze the accessory clamping
u
lever (3).
Slide the accessory (7) between the shaft and the
u
accessory holder making sure the accessory engages all
eight pins on the holder and is flush with the shaft.
Release the accessory clamping lever.
u
Note: Some accessories, such as scrapers and blades can be
mounted at an angle if required (fig. E).
Removing a BLACK+DECKER accessory (fig. C)
Hold the tool and squeeze the accessory clamping
u
lever (3).
Pull the accessory from the tool making sure the
u
accessory dis-engages from all eight pins on the holder.
@
Release the accessory clamping lever.
u
Warning! Gloves must be worn when removing
accessories as they may become hot during
use.
Fitting a sanding sheet (fig. F)
Line up the sanding sheet (8) with the sanding base (7)
u
as shown.
Press the sheet firmly and evenly onto the sanding base,
u
making sure that the holes in the sheet coincide with the
holes in the base.
(Original instructions)
Removing a sanding sheet
@
Pull the sanding sheet off the sanding base (7).
u
Warning! Never use the sanding base without a
sanding sheet or accessory in place.
Fitting alternative accessories (fig. G)
Place the spacer (10) onto the collar (9).
u
Place the alternative accessory (11) onto the collar (9).
u
Firmly attach the fixing bolt (12) into place to ensure a
u
tight fit for the alternative accessory (11).
Note: The spacer and fixing bolt are not used to attach
BLACK+DECKER accessories. BLACK+DECKER
accessories are attached using the Super-lok
accessory clamping lever.
Variable speed control (fig. H)
The variable speed control allows you to adapt the speed of
the tool to the application.
Set the variable speed dial (2) to the desired setting. At
u
setting 1 the tool will operate at low speed, 8,000 min-1.
At setting 6 the tool will operate at the maximum speed,
18,000 min-1.
Switching on and off (fig. I)
To switch the tool on, slide the on/off switch (1) forward
u
(position I).
To switch the tool off, slide the on/off switch (1) to the rear
u
(position O).
LED work light
The LED work light (5) is activated automatically when the tool
is switched on.

Low-battery Indicator

If the LED worklight (5) begins to rapidly and continuously
flash when the switch on the tool is depressed, the battery-
pack power has run out, and the battery pack should
be recharged.
Unlike other battery pack types, Lithium-Ion battery packs
deliver fade-free power for their entire run time. The tool will
not experience a slow, gradual loss of power as you work. To
signal that the battery pack is at the end of its run time and
needs to be charged, the power to the tool will drop quickly.
Note: The LED may also flash due to an overload or high
temperature (see Battery Protection).
Hints for optimum use
Always hold the tool securely. For precision work, hold the
u
tool near the front.
Clamp the workpiece whenever possible, especially when
u
using cutting blades.
Do not exert too much pressure on the tool.
u
ENGLISH
Tool free
TM
9