Custom Settings - Fellowes Cambio Instrucciones

6. RESET THE CONTROL UNIT
While the unit is powered on, press the " " and " " buttons simultaneously until the buzzer beeps. The desk will move down to the lowest position then raise a little. Do not
release the buttons until the process is complete.
7. TROUBLESHOOTING
Error No. Description Solution
Disconnect power for
E01/E07 Electrical problem
30 seconds and reconnect
E02 Screw rod error Reset the system
Check the connection
E04 Digital controller connection error
then reconnect the power
E05 Collision avoidance system Release the button
E06 Electrical problem Replace the control box
E08 Desktop inclines Reset the system
E11 No connection Check the connection (M1)
E12/E22 Abnormal current Replace the control box
Check then replace the motor cord
E13 Motor wire broken
(M1)
Check then replace the motor cord
E14 Hall wire broken
(M1)
E15 Short circuit Replace the motor (M1)
Note:
1. Self-protection function: the unit will enter protective mode if the system operates in excess of two minutes with "HOT" on the control display. The system will
reset and return to normal operation after approximately 20 minutes.
2. Overload protection mode: while operating, if the load on the desk is over weight capacity, the system will enter into an overload protection mode. This will
protect the system from damages caused by exceeding weight. When this happens, the desk will move downward approximately 30mm and come to a stop with
the current height displayed.
3. Attention: NEVER remove or turn off the power in order to reset the unit when it is in a protective mode or "HOT" state.

CUSTOM SETTINGS

For all of the below Custom Settings:
• Press " " and " " simultaneously for 5 seconds until the buzzer beeps once and "S-1" is displayed.
• If no other action is taken within 10 seconds, the process will be automatically canceled.
• The process can be canceled manually by pressing " " at any time.
Custom Setting 1: Minimum & Maximum Height Settings
• Minimum Height Limit: While "S-1" is displayed, press " " once and then press " " or " " to set desired minimum height. Press " " to save: "L-S" = Successful,
"L-F" = Try Again.
• Maximum Height Limit: While "S-1" is displayed, press " " to "S-2". Press " " once and then press " " or " " to set desired maximum height. Press " " to save:
"H-S" = Successful, "H-F" = Try Again.
Note: Default minimum height is 62cm (24.4") and the adjustable range is 62-118cm (24.4"-46.4"). Default maximum height is 128cm (50.4") and the
adjustable range is 72-128cm (28.3"-50.4").
8
CambioBench_411659_RevB_10L_102219.indd 8-9
Error No. Description Solution
E16/E26 Motor failure Reset the system
E17 Desk run in wrong direction Replace the motor cord (M1)
E18/E28 Weight overload Remove the items on the desktop
E21 No connection Check the connection (M2)
E23 Motor wire broken Check then replace the motor cord (M2)
E24 Hall wire broken Check then replace the motor cord (M2)
E25 Short circuit Replace the motor (M2)
E27 Desk run in wrong direction Replace the motor cord (M2)
E42 Memory function failure Replace the control box
Sensor Failure of Collision
E43 Replace the control box
Avoidance System
Custom Setting 2: Adjust the Anti-Collision Sensitivity
• Adjust Upwards Sensitivity: While "S-1" is displayed, press " " to "S-3". Press " " once and then press " " or " " to change the sensitivity level. Default sensitivity
is 2 and the adjustable range is 0-8 (0 = Off, 8 = max.). Press " " to save: "S-S" = Successful, "S-F" = Try Again.
• Adjust Downwards Sensitivity: While "S-1" is displayed, press " " to "S-4". Press " " once and then press " " or " " to change the sensitivity level. Default
sensitivity is 2 and the adjustable range is 0-8 (0 = Off, 8 = max.). Press " " to save: "S-S" = Successful, "S-F" = Try Again.
Custom Setting 3: Adjust the Desktop Tilt Sensitivity
• Adjust Upwards Sensitivity: While "S-1" is displayed, press " " to "S-5". Press " " once and then press " " or " " to change the sensitivity level. Default
sensitivity is 2 and the adjustable range is 0-8 (0 = Off, 8 = max.). Press " " to save: "S-S" = Successful, "S-F" = Try Again.
Custom Setting 4: Adjust to Display the Height With/Without Desktop
• While "S-1" is displayed, press " " to "S-6". Press " " once and then press " " or " " to input desktop thickness. Press " " to save: "T-S" = Successful, "T-F"
= Try Again.
Custom Setting 5: Automatically Lock/Unlock Display
• While "S-1" is displayed, press " " to "S-7". Press " " once and then press " " or " " to choose auto-lock on (1) or to turn auto-lock off (0). Press " " to
save: "A-S" = Successful, "A-F" = Try Again.
To reset the customized settings, press " ", " " and " " simultaneously for 5 seconds until the buzzer beeps.
FELLOWES CAMBIO™ HEIGHT ADJUSTABLE BENCH BASE LIMITED WARRANTY
Fellowes, Inc. (the "Company") warrants the Cambio™ Height Adjustable Bench Base ("Product") to be free from defects in material and
workmanship for the time period as set forth below.
The structural frame for a period of fifteen (15) years from the date of original purchase of the product.
All electrical components for a period of seven (7) years from the date of original purchase of the product.
This warranty applies only to the initial purchaser and does not cover claims resulting from misuse, failure to follow instructions on installation and
use, neglect, use of unauthorized attachments, commercial use, use on a current or voltage other than specified on the product, or unauthorized
service during the warranty period on conditions otherwise covered by warranty.
THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, IS EXPRESSLY LIMITED TO THE DURATION OF THIS LIMITED WARRANTY.
UNLESS REQUIRED BY APPLICABLE LAW, THE CUSTOMER'S EXCLUSIVE REMEDY FOR BREACH OF THIS WARRANTY OR ANY IMPLIED WARRANTY OR OF
ANY OTHER OBLIGATION ARISING BY OPERATION OF LAW OR OTHERWISE SHALL BE LIMITED AS SPECIFIED HEREIN TO REPAIR, REPLACEMENT OR A
REFUND OF THE PURCHASE PRICE, AT THE COMPANY'S SOLE OPTION.
UNDER NO CIRCUMSTANCE WILL THE COMPANY, ITS AFFILIATES, SUBSIDIARIES, RELATED ENTITIES, RESELLERS OR THEIR RESPECTIVE OFFICERS,
DIRECTORS OR EMPLOYEES OR THOSE PERSONS FOR WHOM THEY ARE BY LAW RESPONSIBLE, BE LIABLE FOR CONSEQUENTIAL OR INCIDENTAL
DAMAGES SUSTAINED IN CONNECTION WITH THE PRODUCT. THE COMPANY AND THESE OTHER PARTIES DO NOT ASSUME OR AUTHORIZE ANY
REPRESENTATIVE OR OTHER PERSON TO ASSUME FOR ANY OF THEM ANY OBLIGATION OR LIABILITY OTHER THAN AS IS EXPRESSLY SET FORTH HEREIN.
The duration, terms and conditions of this warranty are valid worldwide, except where different limitations, restrictions or conditions may be required
by local law.
9
10/22/19 4:20 PM