Cub Cadet 37CV3BHK010 Manual Del Operador página 8

Ignition Switch (C)
WARNING
Never leave a running machine unattended. Always shift into park,
stop engine and remove key to prevent unintended starting.
The ignition switch is located to the right of the
steering wheel. To start the engine, insert the
key into the ignition switch and turn clockwise to
the START position. Release the key into the RUN
position once engine has started. To use the high
beam feature, turn the key back to the high beam
position. The high beam indicator in the instrument
cluster will illuminate. See Figure 3-2 & Figure 3-3.
Refer to Starting Engine section of this manual for
detailed starting instructions.
High Beam
Position
Figure 3-3
Gas Pedal (D)
The gas pedal is located to the right of the brake
pedal, beneath the dash panel. See Figure 3-1.
Depressing the gas pedal will move the vehicle in
the direction selected on the shift lever. As the pedal
is slowly depressed, speed will continue to increase
to the desired speed. Releasing the pedal will reduce
the speed, but will not completely stop the vehicle.
The brake must be applied to stop vehicle.
Brake Pedal (E)
The brake pedal is located to the left of the gas pedal,
beneath the dash panel. See Figure 3-1. Remove foot
from accelerator pedal and apply pressure to the
brake pedal until vehicle slows down and stops.
Seat Belts (F)
The seat belts are located on the outside of the
driver and passenger seats. Pull across your chest
and lap and secure it to the seat belt latch located
near the center console.
Note: Seat belt warning indicator will flash for 8 seconds
once the key is turned to the ON position to remind the
operator and passenger to fasten their seat belt.
WARNING
Always wear the seat belt when operating the utility vehicle.
The position of the lap belt portion of the seat belt
should be positioned for both the operator and the
passenger before driving. See Figure 3-4.
Figure 3-4
8 S 3— c
ection ontrolS
Seats (G)
The driver's seat can be adjusted either forward or
rearward. Push the adjustment handle to the right,
slide the seat into the desired position and release
the adjustment handle to lock the seat into place.
See Figure 3-5.
RUN
Position
Note:
START
Position
Bed Tie-Down Rings (H)
The bed tie-down rings can be used to secure items
for transporting.
Differential Lock Lever (I)
The differential lock lever is located in the center
console between the seats. When engaged, the
differential lever locks the rear differential, giving
equal power to both rear wheels. In addition, when
the differential lock lever is in the ON position, the
Differential Lock Indicator located in the instrument
cluster will illuminate. See Figure 3-2.
Shift Lever (J)
The shift lever is located in the center console
P
between the seats and has four positions
(PARK, REVERSE, NEUTRAL and DRIVE). The
brake pedal must be fully depressed when
moving the shift lever. One of the four gear
positions will be displayed in the instrument
R
cluster. See Figure 3-2.
IMPORTANT: Never force the shift lever or
N
attempt to shift while in motion. Doing so may
result in serious damage to the utility vehicle's
D
transmission.
12V Power Outlet (K)
The 12V power outlet is located on the right side
of the dash panel. It is used for the convenience of
plugging in accessories that require a power source
with a maximum load of 7.5A at 12V.
& o
peration
Figure 3-5
The passenger seat is not adjustable.
Auxiliary Switch Panel (L)
The auxiliary switch panel is located on the right
hand side of the dash panel above the handhold.
When adding accessories requiring switches, use
this area of the dash panel to install the desired
switches.
2WD/4WD Switch
The 2WD/4WD switch is located on the
auxiliary switch panel and is used to switch
between 2WD and 4WD. When the 4WD is
activated the front wheels will highlight on
the differential lock/4WD indicator.
Occupant Protective Structure (OPS) (M)
This utility vehicle is equipped with an Occupant
Protective Structure (OPS) and seat belts. When used
together they are effective in reducing crushing
injuries to the operator and passenger in the event
of an accidental rollover or tip-over. The safety
provided by the OPS is minimized if the seat belt is
not properly adjusted AND buckled.
WARNING
Always wear the seat belt when operating the utility vehicle.
Use the following guidelines when using a utility
vehicle equipped with OPS:
1. Be aware of overhead clearances in the area
of operation. Check for clearance of door (or
gate) openings and other overhead objects
such as utility lines and tree branches.
Overhead objects could catch the OPS and
upset the utility vehicle.
2. Do not modify the OPS by drilling holes for, or
welding accessories to, the structure.
3. Do not use the OPS to pull objects with the
utility vehicle. Use ONLY the utility vehicle
hitch for pulling.
4. Do not operate the utility vehicle without the
OPS and do not remove the OPS.
5. In the event of an accident, have the OPS
carefully inspected and, if necessary, replaced
by your Cub Cadet dealer. Do not attempt to
repair the OPS.
Cup Holders (N)
The cup holders are located on top of the dash panel
on both the left and right hand sides.
WARNING
Never operate this vehicle while under the influence of alcohol
or drugs. Doing so can result in serious personal injury or death.
Cargo Bed (O)
The cargo bed maximum capacity is 400 lbs. (181
kg), the passenger + operator max weight is 500
lbs. (226 kg), total cargo bed + passenger/operator
weight (Payload Capacity) is 900 lbs. (408 kg). The
max towing weight is 1200 lbs. (544 kg) and the max
tongue weight is 180 lbs. (81 kg).
The cargo bed may be tilted for dumping loads. Push
forward on the cargo bed latch lever to unlock the
bed and manually lift the cargo bed. See Figure 3-1.
Note: Access to the engine is achieved by raising the
cargo bed.
IMPORTANT: Do not exceed the vehicle's Total
Payload Capacity of 900 lbs (408 kg), which includes
driver, passenger, accessories, tongue load and cargo.
Do not exceed 400 lbs. (181 kg) in the cargo bed.