Cub Cadet 37CV3BHK010 Manual Del Operador página 9

Cargo Bed Latch Lever (P)
The cargo bed latch lever is located on the left/
drivers side of the utility vehicle and is used to
dump/tilt the cargo bed.
Hitch (Q)
The hitch is located on the rear of the utility vehicle
on the frame. The max towing capacity is 1200 lbs.
(544 kg). The max tongue weight is 180 lbs. (81 kg).
Tailgate Latches (R)
The tailgate latches are located on the tailgate and
are used to open the tailgate.
Fuel Cap (S)
The fuel cap is located on the right/passenger's side
of the vehicle to the rear of the passenger's door.
Operation
Tire Inflation
IMPORTANT: Inflation pressure in all tires is 12 psi.
Overinflating above recommended tire pressure can
reduce the life of the tire. Check tire pressures before
each use.
WARNING
Excessive pressure (above 12 psi) may cause the tire/rim assembly
to burst with sufficient force to cause severe injury or death.
Starting Engine
WARNING
This is an off-road utility vehicle and it should not be operated on
public highways. Know and comply with all laws and regulations
governing the use of off-highway vehicles in your area.
IMPORTANT: Before starting the engine, read this
manual and the Engine manual thoroughly to
understand all instructions.
WARNING
Do not run an engine in an enclosed area. Engine exhaust contains
carbon monoxide, which is very poisonous and can cause death.
Move the vehicle outside or to a well ventilated area.
1. While sitting in the seat with your seat belt
fastened, insert key into ignition switch.
2. The engine can be started with the shift lever
in the "P" park position or with the shift lever
in "N" Neutral and the brake held down.
3. Pull out the choke knob if engine is cold.
4. Turn key to the START position.
IMPORTANT: DO NOT run the starter
continuously for more than 5 seconds,
otherwise the battery may discharge quickly.
5. Release key to the RUN position when engine
starts.
6. If engine does not start, wait a few seconds
and repeat steps 4 & 5.
7. After engine starts, push in choke knob.
8. Place shift lever in the desired gear, release
brake and press accelerator pedal slowly.
IMPORTANT: Do not operate the engine
under full load until engine has warmed up.
Stopping Engine
1. To stop utility vehicle, release accelerator pedal
and depress brake pedal until vehicle comes to
a complete stop.
2. Move shift lever into PARK.
3. Turn key switch to STOP position.
4. Remove the key when not in use.
WARNING
The vehicle may roll if the shift lever is not in the PARK position.
Refueling Fuel Tank
WARNING
Avoid injury from explosion or fire. Do not carry fuel or other
flammable liquids in vehicle or cargo bed.
1. Stop vehicle on a level surface and move the
shift lever into PARK.
2. Turn the ignition key to the STOP position and
remove key.
3. Allow engine to cool for 5 minutes before
adding fuel.
4. Clean area around fuel cap and remove.
5. Fill tank with fresh, unleaded, regular grade
fuel only to bottom of filler neck. Use a
minimum of 87 Octane (10% Ethanol Max.).
6. After refueling, push the fuel cap downward on
the fuel tank fill neck and turn clockwise until it
clicks to tighten. Always re-install the fuel cap
tightly onto the fuel tank after removing.
Driving Utility Vehicle
1. Adjust the operator's seat to the most
comfortable position that allows you to
operate all controls and pedals. See Seats
section in Controls & Operation, page 8.
2. Adjust the seat belt to fit comfortably around
your lap, then buckle the seat belt.
WARNING
Do not operate the vehicle without the OPS in place and the
seat belt fastened securely around your waist and chest.
3. Start the engine as instructed earlier and
make sure the front wheels are turned to the
desired direction of travel.
4. Move the shift lever in the center console
to the desired setting. To avoid damaging
transmission, depress brake pedal fully and
make sure vehicle is completely stopped
before shifting into Forward or Reverse.
WARNING
Do not stop or start suddenly when going uphill or downhill.
Be cautious when changing direction on slopes. Apply brakes
when going down slopes to maintain control of vehicle.
5. Release brake pedal and slowly apply pressure
to the accelerator pedal.
6. Release accelerator and apply brake pedal
evenly and firmly to slow down or stop.
Note: When travelling in reverse, the reverse
speed limiter will not allow the utility vehicle
to travel more than 10 mph.
2WD/4WD
CAUTION
When traveling at road speed, use only 2WD. When driving on
icy, wet or loose surfaces, make sure the vehicle is correctly
loaded to avoid skidding and loss of steering control. Reduce
the speed and engage front wheel drive. Accident may
occur if the vehicle is suddenly braked, such as heavy towed
loads shifting forward causing loss of control. The braking
characteristics are different between two and four wheel
drive. Be aware of the differences and operate carefully.
To activate the 4WD press down on the upper half of
the 2WD/4WD switch. To return to 2WD, press down
on the lower half of the 2WD/4WD switch. Switching
between 2WD and 4WD can be done while the
utility vehicle is in motion. If the wheels are slipping
and/or the utility vehicle is stuck, stop the forward
or reverse motion and then switch between 2WD
and 4WD.
Differential Lock
WARNING
To avoid transmission damage, injury or turf damage, drive
slow when operating utility vehicle with differential lock
engaged as steering response is noticeably reduced. Also, do
not drive the utility vehicle with the differential lock engaged
on concrete, asphalt or any high traction surfaces.
The differential lock lever is located in the center
console between the seats. See Figure 3-1.
Note:
The differential lock can be engaged at
low speeds under low loads, but the following
instructions to engage the differential lock are
recommended.
1. To engage; stop utility vehicle, place into
NEUTRAL, and pull the lever upward into the
ON position. The differential will then lock and
remain so until it is disengaged, giving equal
power to both rear wheels.
:
IMPORTANT Engage the differential as the
last option when stuck in mud or similar
situation or when the left and right side
wheels are turning at slightly different speeds.
2. To disengage the differential lock; stop the utility
vehicle, place the shift lever in NEUTRAL, and
push the differential lock lever downward to the
OFF position.
Loading the Cargo Bed
WARNING
The utility vehicle may become unstable if the cargo bed is
loaded incorrectly. Avoid loose and unsecured loads or uneven
loading of material.
1. Verify cargo bed is securely latched before
loading.
2. Securely anchor all loads in cargo bed and do
not load beyond maximum capacity.
:
Note
The maximum box capacity is 400 lbs.
(181 kg).
3. When loading objects into cargo bed, be sure
load is securely anchored and evenly distributed.
4. Do not load above height of cargo bed.
Load could shift forward striking driver or
passenger or cause driver to lose control of
vehicle.
S 3 — c & o
ection ontrolS
9
peration