Rupes HR81M Instrucciones De Funcionamiento Y Mantenimiento página 10

• RED: from 20% to 0% batteries charge
• RED BLINKING: 0% battery charge: the tool does not start.
Soft start
The soft start guarantee the motor and battery protection and reduce the risk of injury for the operator.
STARTING UP
Before starting-up the tool ensure that:
- the packaging is complete and does not show signs of having been damaged during storage or transport;
- the tool is complete; check that the number and type of components comply with that reported in this instruction booklet;
ACCESSORIES ASSEMBLY
WARNING: Before (dis)assembling the tool assure that the speed regulation Knob (2) is in OFF position
WARNING: Do not force the screw it could break. The maximum allowed screw force is 2Nm. To screw use only
a clockwise direction when the tool is positioned as show in a Fig. 4 and Fig. 6 (to unscrew use counterclockwise
direction).
COUNTERWEIGHT
Push the shaft-locking button (6) (Fig. 1) and screw the unit on a tool shaft. Use the provided key to hold a counterweight
(Fig.3).
DISC PAD OR BRUSH (provided or optional)
Dual action version (Fig.4): place the disc pad/brush in the red/blue shaft (4) and screw this one on a shaft (holding it with a
provided key). To remove, hold the shaft with a provided key and unscrew.
Rotary version (Fig.5): place the disc pad/brush in a green shaft (4), hold the shaft locking button (6) and screw the disc pad
on a shaft (Fig. 6), To remove, hold the shaft locking button (6) and unscrew.
BUFFER PAD (Not provided)
CAUTION: Accessories must be rated for at least the speed recommended on the tool-warning label.
Accessories running over rated speed can fly apart and cause injury. Accessory ratings must always be above tool
speed as shown on tool nameplate.
Assemble the buffer pad (3) (Fig. 7) on the velcro surface of the disc pad (4). Press the buffer pad to attach it to the disc pad.
BATTERY PACK (PROVIDED OR OPTIONAL)
WARNING: Avoid short circuiting the contacts. Avoid mechanical damage of the battery pack. Do not open or
disassemble. Advice on protection against fire and explosion. Keep away from open flames, hot surfaces and
sources of ignition.
Temperature in excess of 45°C reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine.
Storage at room temperature (approx. 20°C) at approx. 20~60% of the nominal capacity. Every six months of storage, charge
the battery pack as normal.
Intended use
The battery pack 9HB120LT (Fig. 9) is used as the power source for Rupes BIGFOOT NANO Hybrid tool HR81M/HR81ML.
Battery pack 9hb120lt specifications
WARNING: for technical data refer to the label of Battery pack 9HB120LT
WARNING: to reduce the risk of injury or explosion, never burn or incinerate a tool's battery pack even if it is
damaged, dead or completely discharged. When burned, toxic fumes and materials are created.
Model Chemistry
9HB120LT Lithium Ion
WARNING: charge Rupes Li-ION Battery pack 9HB120LT only in the Rupes Li-ION Battery Charger 9HC120LT.
Other types of batteries may cause personal injury and damage. This tool's battery pack and charger are not
compatible with NiCd or NiMH systems.
When to charge
Charge your battery tool when convenient for you and your job. The Rupes BIGFOOT NANO Hybrid tool Battery pack does
not develop "memory" when charged after only a partial discharge. It is not necessary to run down the battery tool pack before
placing it on the charger. Use the led Battery pack 9HB120LT lever indication on the Rupes BIGFOOT NANO Hybrid tool
HR81M/HR81ML to determine when to charge the Rupes Battery pack.
Charge the battery pack 9HB120LT (8)
The battery pack(s) contained in the kit shall be charger before use. The provided battery is charged <30%. In order to charge
connect the Li-ion battery with a charging station 9HC120LT till the charging is completed.
10
Voltage (V) Capacity (Ah)
10.8 2.0
Energy (Wh) Weight (kg)
21.6 0.183 ±0.005
As
In
fix
In
PO
As
In
too
(F
B
En
- t
co
- th
- th
- a
- th
ST
-
S
bo
- S
sw
FA
If
N
De
EN
S
S
U
VI
De
EN
3
U
Di
wo
too
em