Maintenance; Daily Maintenance; Maintenance Schedule - Husqvarna 130 Mark II Manual Del Usuario

1. Put the product in a cool area away from open
sunlight.
2. Let the product cool down for 20 minutes at
minimum.
3. Press the primer bulb again and again for 10-15
seconds.
4. Obey the procedure to start a cold engine. See
start a cold engine on page 17 .
To stop
• Push the stop switch to stop the engine.
Note: The stop switch automatically goes back to its
initial position.
To use a spike bumper
A spike bumper prevents kickbacks and holds the wood
as you cut. The spike bumper is a pivot between the
engine body and the guide bar.
1. Put the lower end of the spike bumper at the correct
hinge width.
2. Press, with your left hand, against the front handle
while you lift the rear handle with your right hand.
3. Saw until you get the correct hinge width.
Note: The hinge must have an equal thickness.
4. Saw more than half of the diameter and then put the
felling wedge into the saw cut.
To fell a tree
1. Remove dirt, stones, loose bark, nails, staples and
wire from the tree.
2. Make a notch 1/3 the diameter of the tree,
perpendicular to the direction of the fall. (Fig. 55 )
3. Make the lower horizontal notch cut. This helps
prevent pinching the saw chain or the guide bar
when the second notch is made.
4. Make the felling back cut (X) a minimum of 50 mm (2
in) higher than the horizontal notch cut. Keep the
felling back cut parallel to the horizontal notching cut
so sufficient wood is left to be a hinge. Do not cut
WARNING: Read and understand the safety
chapter before you clean, repair or do
maintenance on the product.

Maintenance schedule

Make sure that you obey the maintenance schedule.
The intervals are calculated from daily use of the
product. The intervals are different if you do not use the
product each day. Only do the maintenance work that is
found in this manual. Speak to an approved service
18
All manuals and user guides at all-guides.com
5. As the felling back cut nears the hinge, the tree
To
6. When the tree starts to fall, remove the product from
To limb a tree
1. Use larger limbs to hold the log off the ground.
2. Remove small limbs in one cut. (Fig. 60 )
3. Cut branches that have tension from the bottom to
To buck a log
•
•
•
•

MAINTENANCE

center about other maintenance work not found in this
manual.

Daily maintenance

•
•
•
through the hinge. The hinge wood keeps the tree
from twisting and falling in the incorrect direction.
(Fig. 56 ) and (Fig. 57 )
starts to fall. Make sure that the tree can fall in the
correct direction and not rock rearward and pinch the
saw chain. Stop the cut before the felling back cut is
complete to prevent this. Use wedges of wood,
plastic or aluminum to open the cut and let the tree
fall along the necessary line of fall. (Fig. 58 )
the cut. Stop the motor, put the product down and
use the planned escape path. Be careful of limbs
falling from above and monitor your footing. (Fig.
59 )
the top to prevent pinching the saw chain or the
guide bar.
CAUTION: Do not let the saw chain touch
the ground.
If the log has support along its full length, cut from
the top of the log (known as overbucking). (Fig. 61 )
If the log has support on one end, cut 1/3 the
diameter from below the log (known as
underbucking).
If the log has support on the two ends, cut 1/3 the
diameter from the top. Complete the cut by
underbucking the lower 2/3 of the log to touch the
first cut. (Fig. 62 )
If you buck a log on a slope, always stay on the
uphill side of the log. Cut through the log while you
keep complete control of the product. Then release
the cutting pressure near the end of the cut while
tightly holding the rear handle and front handle. (Fig.
63 )
Clean the external surfaces.
Make sure that the trigger lockout and trigger work
correctly.
Clean the chain brake and make sure that it
operates correctly.
862 - 001 - 20.09.2018