Descargar Imprimir esta página

Cleaning Methods; Normal Soiling; Upholstery Cleaning; Transport - Kärcher Puzzi 9/1 Bp Manual Original

Ocultar thumbs Ver también para Puzzi 9/1 Bp:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 30
Emptying the fresh water tank
1. Switch off the device.
2. Briefly operate the lever on the manual nozzle or an-
gle piece to relieve pressure.
3. Disconnect the manual nozzle or angle piece from
the spray/suction hose.
4. Hang the suction hose in the fresh water tank.
5. Press the suction switch to switch on the suction tur-
bine.
6. Suck the fresh water tank empty and switch off the
device.
7. Remove the cover.
8. Remove the wastewater container from the device
and empty it.
Flushing the device
1. Connect the manual nozzle or angle piece (with suc-
tion pipe and floor nozzle) to the suction hose.
2. Connect the spray hose coupling to the manual noz-
zle or angle piece and latch into place.
3. Pour approximately 2 litres of tap water into the
fresh water tank. Do not add detergents.
4. Press the spray switch to switch on the spray pump.
5. Hold the manual or floor nozzle over a drain.
6. Operate the lever on the manual nozzle or angle
piece and flush the device for 1 to 2 minutes.
7. Switch off the device.
8. Remove the wastewater container from the device
and empty it.
Each time after use
1. Flush the device.
2. Drain the wastewater container and clean it under
running water.
3. Empty the fresh water tank.
4. Clean the exterior of the device with a damp cloth.
5. To avoid unpleasant smells, remove all water from
the device before long downtimes.
6. Let the device dry thoroughly: Remove the cover or
move it to the side.
7. Clean the fluff filter and fresh water filter (see "Care
and maintenance").
Storing the device
1. Store the spray/suction hose and manual nozzle as
shown in the illustration.
Illustration C
2. Store the device in a dry room and secure it against
unauthorised use.

Cleaning methods

Normal soiling

1. Spray and vacuum up the cleaning solution in one
step.
Note
Repeated vacuuming without spraying shortens the dry-
ing time.
Heavily soiling or stains
1. Apply cleaning solution with the suction turbine
switched off and let it work for 10 to 15 minutes.
2. Clean the area as with normal soiling.
12

Upholstery cleaning

1. Adv only: Fit the manual nozzle instead of the floor
nozzle.
2. Use less detergent for sensitive fabrics and spray
the surface at a distance of approx. 200 mm. Then
only vacuum.
● Spray heavily soiled areas in advance and allow the
cleaning solution to work for 5 to 10 minutes.
● Always work from light to shadow (from window to
door).
● Always work from the cleaned to the uncleaned ar-
ea.
● The more sensitive the covering (oriental bridges,
Berber, upholstery fabric) the lower the concentra-
tion of detergent.
● Carpets with jute backs can shrink and bleed in col-
our if the work is too wet.
● Brush wet pile carpets in the direction of the pile af-
ter cleaning when wet (e.g. with a fibre brush or
scrubber).
● Impregnating after wet cleaning prevents the textile
from being quickly soiled again.
● To avoid pressure points or rust stains, do not walk
on or furnish the cleaned area until after it has fully
dried.
● To improve the cleaning result, rinse the object with
clean water after using detergents.
Description
CarpetPro clean-
er (0.8 kg)
CarpetPro clean-
er, iCapsol (16
piece)
CarpetPro clean-
er, quick-drying
(10 litre)
CarpetPro clean-
er (10 litres)
CarpetPro im-
pregnation (5 li-
tres)
Defoaming (2.5 li-
tres)
For further information, please request the product in-
formation sheet and the EU safety data sheet for the rel-
evant cleaning agent.
CAUTION
Failure to observe the weight
Risk of injury and damage
Be aware of the weight of the device during transporta-
tion.
1. Place the suction pipe on the carrying handle of the
device.
Illustration D
2. When transporting the device in vehicles, secure it
to prevent it from slipping or overturning in accord-
ance with the respective valid guidelines.
English
Cleaning tips
Detergent
Name
Metering
Order num-
ber
RM 760
1 %
6.295-175.0
powder
RM 760
2 tabs for 8
6.295-850.0
tabs
litres
RM 767 liq-
1.2 %
6.295-198.0
uid
RM 764 liq-
1 %
6.295-854.0
uid
RM 762 liq-
20 %
6.295-852.0
uid
RM 761 liq-
0.5 %
6.291-389.0
uid

Transport

Publicidad

loading

Este manual también es adecuado para:

Puzzi 9/1 bp packPuzzi 9/1 bp advPuzzi 9/1 bp adv pack1.101-700.01.101-703.01.101-702.0