EINHELL TE-TS 254 T Manual De Instrucciones Original página 28

•
To fasten the stop rail (23) to the parallel stop
(7) you must slacken the two knurled screws
(26). Then thread the stop rail (23) with the
slot (25) onto the lock bolts (28) and secure it
with the washers (27) and the knurled screws
(26).
•
The parallel stop (7) can also be used without
the stop rail (23) when making longitudinal
cuts in wider wooden workpieces (see Fig.
15b). To do this you must remove the lock
bolts (28), the washers (27) and the knurled
screws (26).
•
Warning! When in use, the stop rail (23)
must always be screwed to the side of the
parallel stop (7) which faces the blade.
7.3.2 Cutting width (Fig. 16)
•
The parallel stop (7) can be mounted on eit-
her side of the saw table (1).
•
The parallel stop (7) must be mounted in the
guide rail (29) of the saw table (1).
•
You can clamp the parallel stop (7) in the re-
quired position by pressing the eccentric lever
(12).
When the table width extension (10) is ret-
racted and/or you want to cut widths of less
than 25 cm:
•
Use the main scale (22) on the guide rail (29)
to adjust the parallel stop (7) to the required
dimension.
When the table width extension (10) is exten-
ded and/or you want to cut widths of more
than 25 cm:
•
Use the main scale (22) to adjust the parallel
stop (7) to the 25 cm angle and secure it with
the eccentric lever (12).
•
To then increase the cutting width, adjust the
rest of the cutting width by pulling out the tab-
le width extension (10) (see 7.6).
•
Read off the set total cutting width from the
additional scale (24). Note! To ensure that the
cutting dimension on the additional scale (24)
is correct, the parallel stop (7) must be set to
the defined dimension of 25 cm on the main
scale (22).
7.3.3 Setting the stop length (Fig. 17)
•
The stop rail (23) can be moved in longitudi-
nal direction in order to prevent the workpiece
from becoming jammed.
•
Rule of thumb: The rear end of the stop co-
mes up against an imaginary line that begins
roughly at the front edge of the blade and
Anl_TE_TS_254_T_SPK13.indb 28
GB
runs at an angle of 45° to the rear.
•
Set the required cutting width
- Slacken the knurled screws (26) and push
the stop rail (23) forward until it touches the
imaginary 45° line.
- Retighten the knurled screws (26).
7.3.4 Readjusting the clamping force (Fig. 20)
Danger! Always ensure that the parallel stop (7)
is clamped securely on the guide rail (29) and
cannot slip.
If required you can readjust the clamping force of
the parallel stop (7) by means of the nut (41) on
the rear side of the parallel stop.
Use the wrench (30/31) for this purpose.
7.4 Cross stop (Fig. 18)
To make cross-cuts in wooden workpieces you
must use the cross stop (14).
•
Slide the cross stop (14) into the slot (21) of
the saw table.
•
Slacken the locking screw (36).
•
Turn the stop rail (34) until the arrow points to
the angle required.
•
Re-tighten the locking screw (36).
•
Check the gap between the stop rail (34) and
the saw blade (4).
•
Warning! Do not push the stop rail (34)
too far toward the blade (4). The distance
between the stop rail (34) and the blade (4)
should be approx. 2 cm.
•
If necessary, slacken the two knurled screws
(35) and adjust the stop rail (34).
•
Retighten the knurled screws (35).
7.5 Setting the angle (Fig. 13, 14)
•
Slacken the locking grip (45) and the locking
lever (9).
•
Adjust the angle of the saw blade by pushing
the hand wheel (8) until the pointer is aligned
with the desired angle setting on the angle
scale.
•
Secure the angle by tightening the locking
lever (9).
•
Secure the angle setting in addition with the
locking grip (45) on the rear of the machine.
•
If required, the end stop for the angle setting
of the blade can be readjusted at 0° and at
45°. This is done by adjusting the two adjust-
ment screws (32) and (33).
- 28 -
10.01.2022 08:56:40