Machine'S Safety Equipment - stayer MULTI GAS CUTTER B Manual De Instrucciones

gb
SAFETY WARNINGS GASOLINE
7.
WARNING: Use extra care in handling fuels.
They are flammable and the vapours are
explosive. The following points must be
observed.
- Use only an approved container.
- Never remove the fuel cap or add fuel with the power
source running. Allow engine exhaust components to
cool before refueling.
- Do not smoke.
- Never refuel the machine indoors.
- Never store the machine or fuel containers inside, where
is an open flame, such as a water heater.
- If fuel is spilled, do not attempt to start the power source,
but move the machine away from the area of spillage
before starting.
- Always replace and securely tighten the fuel cap after
refueling.
- If the tank is drained, this should be done outdoors.

MACHINE'S SAFETY EQUIPMENT

8.
WARNING! Never use a machine with faulty safety
equipment. The machine's safety equipment must be
checked and maintained as described in this section.
If your machine fails any of these checks contact your
service agent to get it repaired.
8.1 Throttle lockout
- The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the
lock-out (A) (i.e. when you grasp the handle) it releases
the throttle trigger (B). When you release the handle the
throttle control and the throttle lockout both move back
to their original positions. This movement is controlled
by two independent return springs. This arrangement
means that the throttle control is automatically locked at
the idle setting. (Fig. 1).
- Make sure the throttle control is locked at the idle setting
when (Fig. 2).
- Press the throttle lockout and make sure it returns to its
original position when you release it. (Fig. 3).
- Check that the throttle control and throttle lockout move
freely and that the return springs work properly. (Fig. 4).
- See instructions under the heading Start. Start the
machine and apply full throttle. Release the throttle and
check that the cutting attachment stops and remains
at a standstill. If the cutting attachment rotates with
the throttle in the idle position then the carburetor idle
setting must be checked. (Fig. 5).
8.2 Engine switch (Fig. 6)
Press down the "O" side of the engine switch to stop the
engine.
Start the engine and make sure the engine stops when
you move the engine switch to the stop setting.
ENGLISH
36
8.3 Vibration damping system (Fig. 7)
Your machine is equipped with a vibration damping system
that is designed to minimize vibration and make operation
easier.
Using incorrectly wound cord or a blunt or incorrect
cutting attachment (wrong type or incorrectly filed, see
instructions under the heading Filing the blade) increases
the level of vibration.
The machine's vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine's handle unit.
Regularly check the vibration damping units for cracks or
deformation.
Check that the vibration damping element is undamaged
and securely attached.
8.4 Quick release
There is an easily accessible, quick release fitted near the
suspension ring as a safety precaution in case the engine
catches fire, or in any other situation that requires you to
free yourself from the machine.
8.5 Muffler
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
Never use a machine that has a faulty muffler.
Regularly check that the muffler is securely attached to
the machine.
The inside of the muffler contain chemicals
that may be carcinogenic. Avoid contact with
these elements in the event of a damaged
muffler.
Bear in mind that: The exhaust fumes from the
engine are hot and may contain sparks which
can start a fire. Never start the machine indoors
or near combustible material!
CUTTING EQUIPMENT (CUTTING ATTACHMENT &
9.
GRASS TRIMMER)
This section describes how to choose and maintain your
cutting equipment in order to:
- Reduce the risk of blade thrust.
- Obtain maximum cutting performance.
- Extend the life of cutting equipment.
IMPORTANT: Only use cutting attachments with the
guards we recommend! See the chapter on Technical
data. Refer to the instructions for the cutting attachment
to check the correct way to load the cord and the correct
cord diameter.
Keep the teeth of the blade correctly sharpened! Follow
our recommendations. Also refer to the instructions on the
blade packaging.
Always stop the engine before doing any work
on the cutting attachment. This continues to
rotate even after the throttle has been released.
Ensure that the cutting attachment has stopped
completely and disconnect the HT lead from the spark
plug before you start to work on it. Using an incorrect
36