Troubleshooting; Technical Data - Montarbo WIND PRO Serie Manual De Uso

WIND PRO

TROUBLESHOOTING

12
SYMPTON LIKELY CAUSE
Speaker not connected to active AC
No sound
power.
No sound. The speaker is connected to Speaker power cable is faulty or
working AC power but won't come on. improperly connnected.
Signal source (mixer, instrument, etc )
is not sending.
No sound. Speaker comes on.
Faulty cables and connections
Signal sounds distorted and very loud, Excessive input signal, trying to exceed
PEAK light is lit most of the time. the capabilities of the speakers.
Signal sounds distrorted even at
Mixer or other source is overdriven.
moderate volumes, LIMIT light is not lit.
Lots of hiss in the sound, the mixer
Improper gain structure
controls are at very low settings.
Noise or hiss heard at output. Noisy source device
Improper A/C ground or faulty
equipment connected to mixer input.
Hum or Buzz that increases or decreases
when the mixer level controls are moved.
Faulty cable between source equipment
and mixer.
Improper A/C grounding, ground loops
Hum or Buzz
Excessively long unbalanced cable run.
Improper system gain structure
34
WHAT TO DO
Verify that speaker is connected and that the circuit is on
• Re-seat the power cable at both ends.
• Substitute a known-good power cable.
• Check VU meters on the source mixer.
• Verify that the tape or CD is playing.
• Use headphones to verify that the instrument is actually sending
an audio signal
• Disconnect and re-seat signal cables.
• Replace suspected cable withn a known-good cable
• Reduce the output level of the source.
• Turn down the level controls on the speaker.
• Use additional WIND PRO speakers.
Review the Owner's Manual for your mixer and adjust controls as
needed
• Input sensitivity (gain)
• Channel faders
• Master faders Once this is done, review the instructions in the
Quick Start section of this guide.
• Reduce the level settings at speaker. review the Owner's Manual
for your mixer and adjust controls as needed.
• Input sensitivity (gain)
• Channel faders
• Master fader
Disconnect the devices that are connected to your speaker one at a
time. If the npoise goes away, the problme is with the source or the
connectiong cable.
Disconnect or mute channels one at a time to isolete the
problem. Refer to the owner's manual of the faulty equipment for
troubleshooting help.
Substitute a Known-good cable for the suspected faulty cable.
• 'Lift' the audio ground by usign an XLR/F to XLR/M adapter on
one end.
• Re-route audio cables away from AC power and lighting cables.
• Use the balanced outputs (if available) of your mixer or source
equipment to drive your WIND PRO speakers.
• Use a "DI Box" (direct injection) boc to convert your undbalanced
equipment output to a balanced output.
Reduce the INPUT level controls and increase the output level of
your source devices

TECHNICAL DATA

13
WIND PRO 208A WIND PRO 210A
ACOUSTIC FEATURES
System vented - quasi 3- way point source
Frequency range -6dB) 70 hz - 18 kHz 65 Hz - 18 kHz
Coverage 110° conical H 70° x V 50°
Max SPL(peak)
132 dB SPL 135 dB SPL
IECnoise@1m
TRANSDUCER
10" Neodimium Coaxial
8" Neodimium Coaxial loudspeker with voice
loudspeker with voice coil 3",
LF + HF coil 2", Driver 1,1" with voice coil
Driver 1" with voice coil 1.7" 2,4" and with custom
and custom passive fi lter waveguide custom passive
fi lter
8" Neodimium Woofer 10" Neodimium Woofer
Auxiliary LF
with voice coil 3" with voice coil 2,5"
AMPLIFIER FEATURES
Power supply Universal, PFC, Regulated switch mode
Type Class D - 2 Channels
Output power RMS 800 W per Channel
Connections PowerconTRUE1
Protections Thermal protections, Short-circuit/overload
Operating temperature 0°C to 45°C
DSP FEATURES
Preset 4 preset Factory and 4 preser User
DSP 24 bit 96kHz
Filter M-Modelling
Connections 1 XLR Input / 1 XLR Output / 2 x Ethercon (Control + Dante)
Protections Limiter, Clip Limiter
ENCLOSURE
Width 296 mm (11,7 in.) 345 mm (13,6 in.)
Height 551 mm (21,7 in.) 631 mm (24,8 in.)
Depth 373 mm (14,7 in.) 405 mm (16 in.)
Net Weigh 20 kg (44,09 lb) 25,80 kg (56,87 lb)
Housing Black Polyurea 15 mm Birch Plywood Black painted Steel
12 x M10 Flying Points, 1 12 x M10 Flying Points,
Hardware Top Handle D. 35 mm Pole 2 Side Handles D. 35 mm
Mount, Metal bracket Pole Mount, Metal bracket
System monitoring M-Connect Ethernet TCP/IP - 1 Gigabit
User manual
WIND PRO 212A WIND PRO 215A
60 Hz - 18 kHz 55 Hz - 18 kHz
H 70° x V 50° H 70° x V 50°
139 dB SPL 141 dB SPL
12" Neodimiun Coaxial 15" Neodimiun Coaxial
loudspeker with voice loudspeker with voice
coil 3", coil 3",
Driver 1,1" with voice Driver 1,1" with voice
coil 2,4" with custom coil 2,4" with custom
waveguide and custom waveguide and custom
passive fi lter passive fi lter
12" Ferrite Woofer 15" Ferrite Woofer
with voice coil 3" with voice coil 3"
1200 W per Channel
384 mm (15,1 in.) 440 mm (17,3 in.)
731 mm (28,8 in.) 911 mm (39 in.)
433 mm (17,0 in.) 495 mm (19,5 in.)
38,30 kg (84,43 lb) 46,6 kg (102,73 lb)
7 x M10 Flying Points,
2 Side Handles D. 35 mm
Pole Mount Built-in hardware for suspension
35