Battery Maintenance; Noise And Vibration Levels - Virutex FRB300 Manual De Instrucciones

Dust extraction keeps the workplace clean, prevents dust
build-up in the air and facilitates waste elimination.
Is equipped with a dust extraction adaptor 21 to
which the nozzle (optional accessory) 8204262 can
be connected together our standard dust collection
attachment ref. 6446073 (2.25 m) or 1746245 (5 m)
(optional accessories) to our dust collectors AS182K,
AS282K, ASM582T, ASC682 or to any industrial dust
collection system.
CAUTION: Always use a dust collector designed in accor-
dance with the applicable guidelines on sawdust emission.
11. MAINTENANCE
Remove the battery from the power tool
before carrying out work on the power
tool.
11.1 CLEANING OF THE POWER TOOL
An indispensable condition for a safe long-term exploi-
tation of the power tool is to keep it clean. Regularly
flush the power tool with compressed air thought the
ventilation slots 2.

12. BATTERY MAINTENANCE

• Charge the battery cartridge 8 before completely
discharged. Stop operation in low power and charge
it immediately.
• Do not overcharge when the battery 8 is full, other-
wise it will shorten the life time.
• Charge the battery cartridge 8 with room temperature
at 10° C - 40° C (50°F to 104°F). Charging the battery
in temperatures out of this range can damage it and
may cause fire.
• Charge battery 8 every 6 months without operation
for a long time.
• Replace worn out batteries in time. Decline of pro-
duction or a significantlyshorter runtime of the power
tool after charging indicates aging of the battery 8
and the need for replacement. It should be taken into
account that the battery 8 may discharge faster if the
works take place in the temperature below 0°.
• In case of long time storage without use, it is recom-
mended to store the battery 8 at room temperature, it
should be charged to 50%.
Technical service:
a) To maintain product safety and reliability, repairs, any
other maintenance or adjustment should be performed
by authorized service senters, always using original
replacement parts.
b) Do not repair damaged batteries. Maintenance of the
batteries should be performed only by their producer or
authorized service center.
Transport of Li-Ion batteries
The contained Li-Ion batteries are subject to the
Dangerous Goods Legislation requirements. The user
can transport the batteries by road without further
requirements.
When being transported by third parties (e.g.: air trans-
port or forwarding agency), special requirements on
packaging and labelling must be observed. For prepa-
ration of the item being shipped, consulting an expert
for hazardous material is required.
Dispatch batteries only when the housing is undamaged.
Tape or mask off open contacts and pack up the battery
in such a manner that it cannot move around in the
packaging. Please also observe possibly more detailed
national regulations
13. ACCESSORIES
3021153 Collet D,8
3021152 Collet D,6
8204262 Dust nozzle
13.1 MILLING TOOLS
There is a wide range of milling bits that allow the rea-
lization of multiple works such as: grooving, profiling,
trimming, dovetailing grooves, etc.
To choose the right tool, consult the specific Virutex
range.
14. RECOMMENDATIONS
Switch off the machine before handling it. Keep the
cable and socket in good condition. Use the trimming
heads and accessories appropiates and corresponding
to the trimming machine you have. They do not fit on
other models.

15. NOISE AND VIBRATION LEVELS

The noise and vibration levels of this device have
been measured in accordance with European stan-
dard EN60745-2-11 and EN 60745-1 and serve as a
basis for comparison with other machines with similar
applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
25