Rear Panel - FONESTAR MPZ-6241 Manual Del Usuario

10.- CLIP: peak signal indicator light. If dimly lit, or occasionally lit, the output volume should be reduced.
MULTIZONE AMPLIFIER MPZ-6241
If the indicator light remains on continuously it is due to the high level of the input signal. The volume
of the input signal, therefore, should be reduced.
INPUT 1
11.- PROT: protection indicator light to signal excessive temperature or overload
12.- POWER: power indicator light.
13.- AC: light indicator for alternating current (AC) operation.
1
14.- DC: light indicator for direct current (DC) operation.
15.- Device ON/OFF switch.
16.- MASTER: MASTER output volume control.

REAR PANEL

MPZ-6241
MULTIZONE AMPLIFIER
POWER CONSUMPTION: 320 W
~ 115 V AC. 50/60 Hz FUSE: T5AL 250 V
~ 230 V AC. 50/60 Hz FUSE: T5AL 250 V
18
1.- ZONES 100 V OUTPUTS 1: to turn zones on/off use the front switches. Only loudspeakers with a
100 V line transformer should be used with the zone selection terminals. Connect the positive terminal
of each zone to the corresponding ZONE 1 to ZONE 6 terminal and the common terminal of each
zone to the COM terminal. Maximum power of each zone is 50 W. The total power connected to the
loudspeakers must not exceed the power of the amplifier, 240 W.
2.- REMOTE MIC: input terminals M-62 microphones. It allows you to connect up to 6 microphones in
cascade in one terminal or 3 microphones in cascade in each terminal.
3.- MUTE: all inputs and the MP3/FM modules are muted when the contacts of these two terminals are
closed.
4.- EMC: emergency signal input connection terminals. This activates all zones and has the highest priority.
5.- TEL: telephone input connection terminals. These allow you to connect to a telephone switchboard to
make pages from the switchboard with priority over the other inputs. Consult the characteristics of the
switchboard to adjust to the input level of the amplifier. This has priority over inputs INPUT 1-6.
6.- VOL: adjusts the volume of the TEL input.
7.- REC OUT: line level output, 2 x RCA connectors.
8.- INPUT: line level inputs. Allows you to connect audio sources, 2 x RCA connectors.
9.- FM ANT.: FM antenna input connection terminals.
10.- INPUT 1-4: microphone/line inputs, XLR combo connector and 6.3 mm jack. Supports balanced
and unbalanced microphone signals and balanced electrect condenser microphones requiring 48 V
phantom power. High level, balanced or unbalanced line signals from mixers, CDs, tape, tuners, etc.
are supported.
11.- LINE/MIC/PHANTOM +48 V: These switches have 3 positions:
- LINE: At this position, LINE 1 to LINE 4 inputs can be connected to line-level audio sources, such
as a pre-amplified desktop microphone or the line-level output of a mixer.
- MIC: In this position, balanced or unbalanced, dynamic or electret condenser microphones can
be connected to the LINE 1 to LINE 4 inputs, powered by a battery that does not require phantom
power.
- PHANTOM +48 V: in this position, electret condenser microphones requiring phantom power
(48 V between pins 3 and 1, 2 and 1 of the XLR connector) can be connected to the LINE 1 to LINE
4 inputs. Use this switch at minimum volume to avoid damage.
4
VOL +
MODE
REC
VOL -
BASS BASS BASS
INPUT 2 INPUT 3 INPUT 4
TREBLE TREBLE TREBLE
2 3
ONE ZONE: 50 W MAX.
TOTAL ALL ZONES: 240 W MAX.
CLASS II WIRING
17
5 6 7 8 9
ALL Z1 Z2 Z3
VOL VOL VOL
BASS BASS BASS
INPUT 5 INPUT 6
TREBLE TREBLE TREBLE
1
INPUT 4
CLASS II WIRING
PUSH
CHIME
CHIME SIREN
GAIN GAIN
LINE PHANTOM +48 V
SIREN COM MIC
16 15 14 13 12
- 3 -
1011 12 13
Z4 Z5 Z6
PROT
VOL VOL VOL
CLIP
SIG
MASTER
17 16
2 3 4 5 6 7 8
REC INPUT
OUT
MUTE EMC TEL
REMOTE MIC
VOL
INPUT 3 INPUT 2
PUSH PUSH
LINE PHANTOM +48 V LINE PHANTOM +48 V LINE PHANTOM +48 V
MIC MIC MIC
11
EN
POWER
14
AC
15
DC
9
INPUT 1
PUSH
10