VONROC MS507AC Traducción Del Manual Original página 15

4. OPERATION
Before you turn on the machine, always
check that the saw blade is fitted correctly.
The blade must turn smoothly.
Always check the protective guards before
use.
For all cuts, it must first be ensured that the
saw blade at no time can come in contact
with the fence, workpiece clamp or other
machine parts. Remove any mounted
auxiliary stops or adjust them accordingly.
Supporting the workpiece (fig. H)
Workpieces must always be properly supported.
The table extensions (10) can be extended left and
right to support a workpiece. To do so:
1. Loosen the locking bolt for table extension (34);
2. Move the table extension (10) to the desired
position;
3. Tighten the locking bolt for table extension (34).
When sawing extra-long workpieces, the free end
of long workpieces must have something additio-
nally placed underneath it or be supported.
Clamping the workpiece (fig. H)
Workpieces must always be firmly clamped. The
workpiece clamp (21) can be placed left and right
of the workpiece. To do so:
1. Ensure the workpiece is firmly pressed against
the fence (9);
2. Insert the supplied workpiece clamp (21) into
one of the holes intended for this purpose, as
can be seen on figure H;
3. Adjust the threaded rod of the workpiece clamp
(21) to the workpiece height;
4. Firmly tighten the threaded rod of the workpie-
ce clamp (21) to fix the workpiece in place. To
loosen, simply untighten the threaded rod of
the workpiece clamp (21).
The knob for workpiece clamp (44) can be used
to more quickly adjust the height of the workpiece
clamp (21). After adjusting the height, always firm-
ly tighten the threaded rod of the workpiece clamp
(21) to fix the workpiece in place.
WWW.VONROC.COM
Adjusting the fence (fig. H)
Always adjust the fence to the specific type
of cut.
When sawing mitre and/or bevel angles, you have
to move the adjustable fence (7) depending on
the cutting direction. This way, the workpiece is
always properly supported by the fence under each
condition. To do so:
1. Loosen the locking bolt for adjustable fence (35);
2. Adjust the fence according to the desired cut.
For mitre or straight cuts the fence has to be
moved inwards towards the blade (max 8 mm)
without touching it. For bevel cuts, the fence has
to be moved outwards away from the blade (max
8 mm) without touching it;
3. Tighten the locking bolt for adjustable fence (35);
4. To ensure the blade won't get in touch with the
adjustable fence (35), it is advised to make a
test run of the movement of the blade, without
turning the machine on.
Adjusting the mitre angle (fig. A)
The mitre angle can be adjusted between 45° left side
and 45° right side. For quick and precise setting of
commonly used mitre angles, presets are provided on
the saw table on 0°, 15°, 22.5°, 30° and 45° angles.
Adjusting the mitre angle to a preset:
1. Loosen the knob for mitre adjustment (14);
2. Pull the lever for mitre adjustment (15) and
rotate the table (11) left or right to the desired
preset. The angle can be read on the scale for
mitre angle (16) using the indicator for mitre
angle (17).
3. Release the lever. The lever must be felt to
engage in the detent of the preset.
4. Tighten the knob for mitre adjustment (14).
Adjusting the mitre angle to any required angle:
1. Loosen the knob for mitre adjustment (14);
2. Pull the lever for mitre adjustment (15) and rotate
the table (11) left or right to the desired position.
The angle can be read on the scale for mitre an-
gle (16) using the indicator for mitre angle (17).
3. Release the lever and tighten the knob for mitre
adjustment (14).
EN
15