Descargar Imprimir esta página

Bosch GWS 11-125 P Professional Manual Original página 24

Ocultar thumbs Ver también para GWS 11-125 P Professional:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 42
24 | English
a
h
K
Disc sanding:
a
h
K
Grinding thin metal sheets or other materials that tend to easily vibrate with a large surface area can cause the noise emission
value to increase by up to 15 dB. Suitable, heavy damping mats can reduce the increased noise emissions. Increased noise
emissions must be taken into consideration, both for the risk assessment of the noise output and for selecting suitable hearing
protection.
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Kickback stop
(GWS 15-125 CIEP)
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically.
Speed preselection
(GWS 15-125 CIEP)
You can preselect the required speed using the speed preselection thumbwheel (4), even during operation. The information in
the table below describes the recommended values.
Material
Application
Metal
Removing paint
Metal
Brushing, removing rust
Stainless steel
Grinding
Metal
Rough grinding
Metal
Cutting
Stone
Cutting
1 609 92A 7AL | (30.03.2022)
GWS 11-125 P
GWS 11-125 P GWS 15-125 CIEP
2
m/s
6.0
2
m/s
1.5
2
m/s
3.0
2
m/s
1.5
To restart the tool, set the On/Off switch (3) to the "off" po-
sition and then switch the power tool on again.
Restart protection
(GWS 15-125 CIEP)
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (3) to the "off" posi-
tion and then switch the power tool on again.
Soft start
(GWS 15-125 CIEP)
The electronic soft start limits the torque when the power
tool is switched on and enables a smooth start-up.
Note: If the power tool runs at full speed immediately after
being switched on, this means that the soft start and restart
protection mechanisms have failed. The power tool must be
sent to the after-sales service immediately; see the "After-
Sales Service and Application Service" section for ad-
dresses.
Constant Electronic control
(GWS 15-125 CIEP)
The Constant Electronic keeps the speed at no load and un-
der load virtually consistent, guaranteeing uniform perform-
ance.
Application tool
Sanding sheet
Cup brush, abrasive disc
Grinding disc/fibre disc
Grinding disc
Cutting disc
Diamond cutting disc
6.0
6.0
1.5
1.5
3.0
3.0
1.5
1.5
Thumbwheel position
2–3
3
4–6
6
6
6
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

Gws 15-125 ciep professional