Panasonic CQ-RX400N Manual De Instrucciones página 13

Troubleshooting (continued)
Display
A USB device that exceeds the current capacity that can be supplied was
connected. For some reason, an over-current was detected.

Use a USB memory that has a consumption current of less than 500 mA.

Switch the Source, and select USB (MP3/WMA/AAC) mode again.

Check that the USB connector section is not dirty, and that there is no
foreign material.
No operation by some cause.

Switch the power or ACC ON/OFF. If this does not solve the problem, unplug
the power cord and plug it in again. In case the unit is still out of order,
consult your dealer. (
The player for some reason cannot read the fi le you are trying to play. (File
recorded in an unsupported fi le system, compression scheme, data format, fi le
name extension, damaged data, etc.)
(After 5 seconds)

Confi rm that the USB extension cable is fi rmly connected, and reconnect if
not. Select a fi le that the player can read. Check the type of data stored in
To next fi le automatically
the USB memory. Format the USB memory if necessary.
A WMA/AAC fi le can be copyrighted.
(After 5 seconds)

The fi le protected by copyright is not playable.
To next fi le automatically
The iPod was not recognized correctly.

It could take some time for the iPod to be recognized.

Check the connection.

Reset the iPod, then connect it again.
Your iPod has no playable music.

Download playable music to your iPod.
The disc is dirty or upside down.

Check the disc.
The disc has scratches.

Eject the magazine.
(After 5 seconds)
• Check the disc.
• Load the disc again.
The next disc automatically
No operation by some cause.

Eject the magazine. If failure persists, press the reset switch on the CD
changer. If normal operation is not restored, consult your dealer or the
nearest Panasonic Service Centre to ask for repairs.
No disc is in the CD Changer (magazine).

Insert discs into the CD changer (magazine).
The changer has become disconnected from the unit in the changer mode.

Verify the wiring.
Note: Messages in the action and display sections of the error chart vary with changer. Refer to the operating
instructions for the CD changer for details.
24
CQ-RX400N/CQ-RX300N/CQ-RX200N
All manuals and user guides at all-guides.com

Possible cause Possible solution

Installation Instructions)
Problem Possible cause
This unit does not display The Bluetooth Unit and Bluetooth device are too far apart.

the pairing screen when Bring the Bluetooth Unit and Bluetooth device closer together and try to pair
again.
trying to pair a device.
The voice of the other party heard from the car speakers is being picked up by the
microphone of the Bluetooth Unit and returned to the other party.

The other party in the call Close the windows.

complains of echoing or Move the Bluetooth Unit microphone away from the car speakers.

Lower the volume.
noise.

Set Speaker Selection Setting to "SP LEFT" or "SP RIGHT".

Set the Echo Cancel Setting to "EC HIGH".
Telephone audio is of poor quality. Cellular phone reception is poor.

Telephone audio is inaudible. Check cellular phone reception.
The Bluetooth audio-compliant device does not support AVRCP (Audio/Video
Bluetooth audio does not Remote Control Profi le).

work. Check the instruction manual of the Bluetooth audio-compliant device for
support conditions.
Display Possible cause
Communication with the Bluetooth device is not possible in the Bluetooth mode.

Check the connection.

Verify the wiring.
The Bluetooth Hands-Free device is not connected in the Bluetooth Hands-Free
mode, or it is not paired with this unit.

Pair and connect the Bluetooth Hands-Free device with this unit.
If a Bluetooth Audio device is not detected in 2 minutes during pairing, "TIME
(After 5 seconds)
OUT" is displayed and pairing is canceled.

Pair and connect the Bluetooth Audio device with this unit.
If a Bluetooth Hands-Free device is not detected in 2 minutes during pairing,
(After 5 seconds)
"TIME OUT" is displayed and pairing is canceled.

Pair and connect the Bluetooth Hands-Free device with this unit.
Pairing Bluetooth Audio device is canceled because the PIN code does not match.

(After 5 seconds) Set the PIN code for this unit.
Profi le of the Bluetooth Audio device is not matched.

Connect the Bluetooth Audio device with profi le supported this unit.
Pairing Bluetooth Hands-Free device is canceled because the PIN code does not
match.
(After 5 seconds)

Set the PIN code for this unit.
Profi le of the Bluetooth Hands-Free device is not matched.

Connect the Bluetooth Hands-Free device with profi le supported this unit.
(After 5 seconds) A paired Bluetooth Hands-Free device could not connect to this unit.

Connect the paired Bluetooth Hands-Free device.
CQ-RX400N/CQ-RX300N/CQ-RX200N

Possible solution

Possible solution
25