Publicidad
ENGLISH
INTRODUCTION
This BACKEYE system has been designed to provide years of trouble-
free operation. Please read this manual thoroughly. This manual con-
tains instructions to make the installation of the camera and monitor
easier. This BACKEYE system is a supplement to standard rear-view
mirror systems, and will provide additional rear-view vision when
installed and maintained properly. It is not intended in any way to be a
substitute for careful and cautious driving. All applicable traffic laws
and motor safety regulations must still be adhered to.
FEATURES
BE-100C CAMERA
• Auto White Balance (AWB)
• Back Light Compensation (BLC)
• 290,000 pixel image sensor
• 6 Infra-Red LED
• Min 0.5 Lux sensitivity
• Automatic electronic iris provides a clearer, more consistent image
in low and bright light
• Wide-angle lens (130° Diag.) provides a broad viewing area
• Compact design and lightweight ease installation in most vehicles
• Waterproof Aluminum Die-Casting Housing
• Built-in microphone for audio pick up (See Fig. 6)
• Waterproof cable connection
• Fully Waterproof (IP67)
• Sun-Shield
• CE/e-marking
BE-145M MONOCHROME 4.5" MONITOR
• FCC/CE/e-marking
• Automatically picture is displayed in a reverse gear
• Day/night switch
• Audio/Video output for recording
• Built-in speaker
• Volume control
• Brightness control
• Mirror/Normal Image Switch
• 2 camera inputs
• Camera 1/Camera 2 Selector Switch
• Power/stand-by switch
CONTENTS OF 1 COMPLETE SYSTEM
BE-100C CCD CAMERA
1-Camera
1-Camera bracket
4-Attachment screws with washers (M4 x 15)
8-Attachment screws with washers (M5 x 15)
1-Wind deflector
BE-145M 4.5" MONOCHROME MONITOR
1-Monitor
1-Snap-on sun visor
1-Monitor bracket
1-Power harness with locking connector
1-Range markers
4-Thumb screws (M5 x 12)
Special Cable: 1-20 meter cable with waterproof connector. Oil, gas,
grease resistant. UV stable
BEFORE INSTALLATION
1. This system operates from 12 volts DC to 32 volts DC, negative
ground.
2. Please install this system according to the instructions in this manu-
al.
3. Do not disassemble the camera or the monitor. This voids the war-
ranty. Disassembling the camera will compromise the Waterproof
seal.
4. Connect the system to an ignition switched power source.
Connection to a battery source will reduce battery life.
WARNING
1. To prevent electrical shock, DO NOT OPEN THE MONITOR CASE.
There are potentially lethal voltages inside the monitor. There are no
user serviceable parts inside. If evidence of tampering is detected,
the warranty will be considered void.
2. Keep monitor away from leaking water, rain, moisture etc. It is NOT
waterproof. Any moisture inside the monitor could cause extensive
damage.
3. Use the thumbscrews to mount the monitor to bracket.
4. Do not cover air ducts. Monitor needs proper ventilation to prevent
overheating.
INSTALLATION INSTRUCTIONS
BE-100C CAMERA
1. Attach camera bracket (see Fig. 1) to upper portion of vehicle.
BE-145 BACKEYE REARVIEW CCTV SYSTEM
Attachment point must be sturdy enough to support camera and
bracket.
2. Attach camera to bracket using M4 bolts provided. Adjust angle as
indicated in Fig. 2. (Use rear bumper and back of vehicle as a refer-
ence point.)
3. Wind deflector may be installed. The deflector is designed to reduce
the build up of dust, dirt and moisture on the camera lens. (See
Fig.3.)
BE-145M MONITOR
1. Attach monitor inside vehicle in a suitable position for the driver
(e.g. centre of dash, overhead or in dash). (See Fig.4.)
2. Use a compression plate to attach the monitor bracket to the dash
or overhead. (See Fig. 4.)
3. Adjust mounting angle of the monitor to allow driver to easily view
the screen from all seat positions. (See Fig. 4.)
4. If necessary snap sun visor into groove on front face of monitor.
Press all (4) sides of the visor to snap it into place.
CABLE
1. The camera to cable connection is waterproof. The cable to monitor
connection is not waterproof. Be sure to position the cable properly.
The female end attaches to the camera. The 4-pin male mini din end
attaches to the monitor. (See Fig. 5.)
2. Do not run the cable over sharp edges or corners. Do not kink the
cable. Keep the cable away from hot and rotating parts.
3. Place all excess cable in convoluted tubing.
4. Wire the cable securely.
WIRING CAMERA AND MONITOR
1. See wiring diagram for connections to ignition, ground and back up
circuit. (See Fig. 5.)
2. Wiring camera: Drill a 22mm diameter hole into vehicle body near
the camera and bracket. Connect camera connector to extension
cable in vehicle. Push extra cable into vehicle (be careful not to kink
cable) and fit grommet into hole. Apply sealant around grommet to
increase resistance to water penetration.
3. Wiring Monitor: Insert extension cable into camera #1 position.
If 2 cameras are used, be sure to mark each extension cable proper-
ly and plug second cable into camera #2 position. Bundle excess
cable together using a cable tie or vinyl tape. This will avoid possi-
ble damage to cable during operation.
4. The red wire is connected to an ignition power source, the black
wire is connected to chassis ground, and the blue wire is connected
to the vehicle's reversing light circuit.
FUNCTIONS AND OPERATION
1. POWER
Press the power switch to turn the monitor on and off
When reverse gear is selected the images picked up by camera 1
will be shown on the monitor
2. CAMERA SELECTOR
Depress the camera button (*CA1) to select the camera connected
to camera 1.
Press the camera button (*CA2) to select the camera connected to
camera 2.
3. NIGHT/DAY
When viewing pictures at night or in a tunnel change the picture
brightness by pressing the night/day switch
4. BRIGHTNESS
The brightness can be adjusted to suit settings for "DAY/NIGHT"
5. VOLUME
Adjust the volume control for the desired sound level
6. POWER SOCKET
Insert the supplied power cable connector firmly until it is locked
To remove the power connector, press in the clip and pull out the
connector, while holding the clip down
(Camera 1 & Camera 2 are operated individually)
7. NORMAL/MIRROR
When the switch is in MIR position, the picture will show reverse
image
When the switch is in NOR position, the picture will show a normal
image
(Camera 1 & Camera 2 are operated individually)
8. AUDIO/VIDEO OUTPUT
Connect audio, video output connector to a second monitor or VCR
input with a RCA phone type connector cable
9. CAMERA INPUT SOCKET
There are two mini DIN type sockets for the video camera input
CAUTION
1. DO NOT OPEN THE CAMERA CASE. This will break the camera's
waterproof seal. If evidence of tampering is detected, the warranty
will be considered void.
2. We do not recommend mounting the camera near the lower area of
the vehicle (e.g. bumper). This reduces the view of the camera and
increases the chance of physical damage to the camera.
3. Use only the Inner Hexagonal screw and washers to mount the
camera.
MAINTENANCE
Remove dust and dirt with a damp soft cloth. Heavier dirt should be
removed with a damp soft cloth and mild detergent. Do not use strong
cleaning agents containing gasoline, thinner, benzene or alcohol. These
substances may damage the exterior surface of the monitor.
CAUTION
1. Before drilling, be sure no cable or wiring is on the other side. Be
sure to drill a 22mm diameter hole only.
2. Feed as much cable as possible into vehicle and clamp securely.
This reduces the possibility of it being hooked or snagged.
3. Keep all cables away from HOT, ROTATING and ELECTRICALLY
NOISY components.
4. To increase protection of cable, place all excess wire and extension
cable in convoluted tubing.
5. Do not twist camera cable and do not cut camera pigtail or cable.
SPECIFICATIONS
BE-100C CAMERA
VIDEO SYSTEM
NTSC/PAL
PICK-UP DEVICE
CCD
IMAGE SIZE
1/3 inch
SYNCHRONIZATION
INTERNAL
REQUIRED ILLUMINATION
0.5 lux MINIMUM
VIDEO OUTPUT
1V (p-p), 75 ohm
OPERATING VOLTAGE
12 Vdc
POWER CONSUMPTION
MAX 2.4W (AT 12V DC)
OPERATION TEMPERTURE
-30°C TO +50°C
WEIGHT
0.25Kg
DIMENSION (W x H x D) mm
69 x 11 x 59
BE-145M MONOCHROME 4.5" MONITOR
VIDEO SYSTEM
EIA/CCIR
PICTURE TUBE
4.5 inch B/W Monochrome Screen
PICTURE RESOLUTION
525 TV LINES
INPUT SIGNAL
1Vp-p (75ohm)
AUDIO OUTPUT
0.3 W
POWER CONSUMPTION
MAX 14 W
OPERATION TEMPERTURE
-10°C TO + 60°C
OPERATION VOLTAGE
10 Vdc TO 32 Vdc
WEIGHT APPROX.
1.3Kg
DIMENSION (W x H x D) mm
137 x 126 x 163
DISCLAIMER
The use of the BE-145 BACKEYE Observation system should not in any
way be used as a substitute for careful and cautious driving. Traffic
laws and motor safety regulations must always be adhered to.
Publicidad
