Publicidad
Idiomas disponibles
Idiomas disponibles
General Power Tool Safety Warnings
WARNING! Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference!
The term "power tool" in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as
in the presence of flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power
tool. Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug
in any way. Do not use any adapter plugs with earthed (ground-
ed) power tools. Unmodified plugs and matching outlets will re-
duce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased
risk of electric shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water en-
tering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling
or unplugging the power tool. Keep cord away from heat, oil,
sharp edges or moving parts. Damaged or entangled cords in-
crease the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.
f) If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense
when operating a power tool. Do not use a power tool while you
are tired or under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result
in serious personal injury.
b) Use personal protective equipment. Always wear eye protec-
tion. Protective equipment such as dust mask, non-skid safety
shoes, hard hat, or hearing protection used for appropriate con-
ditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the
off-position before connecting to power source and/or battery
pack, picking up or carrying the tool. Carrying power tools with
your finger on the switch or energising power tools that have the
switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power
tool on. A wrench or a key left attached to a rotating part of the
power tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situa-
tions.
f) Dress properly. Do not wear loose clothing or jewellery. Keep
your hair, clothing and gloves away from moving parts. Loose
clothes, jewellery or long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction
and collection facilities, ensure these are connected and prop-
erly used. Use of dust collection can reduce dust-related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer
at the rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and
off. Any power tool that cannot be controlled with the switch is
dangerous and must be repaired.
c) Disconnect the plug from the power source and/or the battery
pack from the power tool before making any adjustments,
changing accessories, or storing power tools. Such preventive
safety measures reduce the risk of starting the power tool acciden-
tally.
d) Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instruc-
tions to operate the power tool. Power tools are dangerous in the
hands of untrained users.
e) Maintain power tools. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that
may affect the power tool's operation. If damaged, have the
power tool repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting
tools with sharp cutting edges are less likely to bind and are easier
to control..
g) Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working con-
ditions and the work to be performed. Use of the power tool for
operations different from those intended could result in a hazard-
ous situation.
5) Service
a) Have your power tool serviced by a qualified repair person us-
ing only identical replacement parts. This will ensure that the
safety of the power tool is maintained..
Safety Instructions for Saws
with Linear Reciprocating Motion
– During activities where the cutting tool may touch hidden ca-
bling or its own lead, the power tool must be held by the in-
sulated gripping surfaces. The cutting tool coming into contact
with a live conductor may cause metal parts of the power tool to
become live as well and cause injury by electric current to the user.
– Use clamps or other practical method of securing and propping
up the workpiece on a stable base. Holding the workpiece by
hand or propped up against the body leads to its instability and
can cause the user to lose control of the tool.
Charger safety warnings
– This appliance is not designed for use by other people (children
included), physical, sensory or mental incapability or lack of ex-
perience and knowledge of whose prevent from safe use of the
appliance without being supervised, or without being instructed
on use of the appliance by a person responsible for their safety.
– Children should be supervised to avoid their playing with the ap-
pliance.
Information about noise level
and vibrations
The values have been measured in conformity with EN 62841-1.
CPO 150
Acoustic pressure level L
= 83.4 dB (A).
pA
Acoustic power level L
= 94.4 dB (A).
wA
In accuracy of measurements K = 5.0 dB (A).
ATTENTION! Noise is generated during work!
Use ear protection!
The weighted value of vibrations affecting hands and arms
a
= 8.62 m.s
.
-2
h
In accuracy of measurements K = 1.5 m.s
The emission values specified (vibration, noise) were measured in ac-
cordance with the test conditions stipulated in EN 62481 and are intend-
ed for machine comparisons. They are also used for making preliminary
estimates regarding vibration and noise loads during operation.
The emission values specified refer to the main applications for which
the power tool is used. If the electric power tool is used for other ap-
plications, with other tools or is not maintained sufficiently prior to
operation, however, the vibration and noise load may be higher when
the tool is used.
Take into account any machine idling times and downtimes to estimate
these values more accurately for a specified time period. This may signif-
icantly reduce the load during the machine operating period.
English
-2
.
19
Publicidad
