Descargar Imprimir esta página

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

COMMERCIAL STYLE
WALL-MOUNT KITCHEN FAUCET
255-K821-T – Chrome finish
255-K821-SS-T – Stainless steel finish
255-K821-MB-T – Matte black finish
PACKAGE AND HARDWARE CONTENTS
PART
DESCRIPTION
A
Spout
B
Faucet body
C
Spray head
D
Swivel union
E
Flange
F
Rubber washer
Due to constant design and quality improvements, the product
may look slightly different from the picture.
SAFETY INFORMATION
Please read and understand this entire manual before attempting to
assemble, operate or install the product.
WARNING
• Protect your eyes with safety glasses when cutting or soldering water
supply lines.
PREPARATION
Before beginning assembly of product, make sure all parts are present.
Compare parts with the package and hardware contents list. If any part is
missing or damaged, do not attempt to assemble the product.
Contact customer service for replacement parts.
Estimated Assembly Time: 30 minutes
Tools Required for Assembly (not included): Adjustable Wrench, Slip Joint
Pliers, Pipe Wrench, Phillips Screwdriver, and Thread Seal Tape.
Questions, problems, missing parts? Before returning to your retailer, call our customer service department at 1-877-319-3757,
7:30 a.m. - 4:30 p.m., CST, Monday - Friday.
Homewerks Worldwide, LLC • Lake Bluff, IL 60044 • Homewerks.com
QUANTITY
1
1
1
2
2
2
CAUTION
• If you solder the joints during installation of the faucet, the seats,
• Cover the sink drain to avoid losing parts.
Installation may vary depending on how the previous faucet was
installed. Supplies necessary for the installation of the faucet are not
all included; however, they are available wherever plumbing supplies
are sold.
Prior to beginning installation, turn off the hot and cold water lines, then
turn on the old faucet to release built-up pressure. When installing the
new faucet, hand tighten the connector nuts. DO NOT OVERTIGHTEN.
Connections that are too tight will reduce the integrity of the system.
A
B
C
cartridges, and washers must be removed before using a flame
or the warranty will be voided on these parts.
F
D
E
05/2022

Publicidad

loading

Resumen de contenidos para TOSCA 255-K821-T

  • Página 1 COMMERCIAL STYLE WALL-MOUNT KITCHEN FAUCET 255-K821-T – Chrome finish 255-K821-SS-T – Stainless steel finish 255-K821-MB-T – Matte black finish PACKAGE AND HARDWARE CONTENTS PART DESCRIPTION QUANTITY Spout Faucet body Spray head Swivel union Flange Rubber washer Due to constant design and quality improvements, the product may look slightly different from the picture.
  • Página 2: Product Specifications

    PRODUCT SPECIFICATIONS Maximum flow rate: 1.8 GPM (6.814 LPM) at 60 PSI Ceramic cartridges ASME A112.18.1/CSA B125 Manufactured to include no more than 0.25% weighted average lead content on wetted surfaces NSF/ANSI/CAN 61 Chrome and stainless steel finishes INSTALLATION INSTRUCTIONS 1.
  • Página 3 TROUBLESHOOTING PROBLEM POSSIBLE CAUSE SOLUTION Faucet leaks Bonnet has come loose or the 1. Move the handle to the OFF position. Unscrew the handle screw and remove the handle. underneath handle. ceramic cartridge seal is dirty or 2. Tighten the bonnet by turning it clockwise. Move the cartridge stem to the ON position. out of place.
  • Página 4: Replacement Parts

    REPLACEMENT PARTS For replacement parts, call our customer service department at 1-877-319-3757, 7:30 a.m. - 4:30 p.m., CST, Monday - Friday. PART DESCRIPTION PART # 255-K821-T 255-K821-SS-T 255-KB21-MB-T RP 00614DCH RP 00614DSS RP 00614DMB Spray head RP 00612DCH RP 00612DSS...
  • Página 5: Grifo De Cocina Estilo Comercial De Pared

    GRIFO DE COCINA ESTILO COMERCIAL DE PARED 255-K821-T – Acabado cromado 255-K821-SS-T – Acabado acero inoxidable 255-K821-MB-T – Acabado negro matte CONTENIDOS DEL PAQUETE Y HARDWARE PARTE DESCRIPCIÓN CANTIDAD Caño del grifo Cuerpo del grifo Cabezal del rociador Unión giratoria...
  • Página 6: Especificaciones Del Producto

    ESPECIFICACIONES DEL PRODUCTO Caudal de flujo máximo: 6,81 LPM (1,8 GPM) a 60 PSI Cartuchos de cerámica Cumple con la norma ASME A112.18.1/CSA B125 Fabricado a incluir no más de 0,25 % de contenido de plomo promedio ponderado en superficies mojadas NSF/ANSI/CAN 61 Acabados en cromo y acero inoxidable INSTRUCCIONES DE INSTALACIÓN...
  • Página 7: Solución De Problemas

    SOLUCIÓN DE PROBLEMAS PROBLEMA CAUSA POSIBLE SOLUCION El grifo tiene una fuga El casquete se ha aflojado o el sello 1. Mueva la manija a la posición APAGADO. Desatornille el tornillo de la manija y retire la manija. debajo de la manija. del cartucho de cerámica está...
  • Página 8: Piezas De Repuesto

    PIEZAS DE REPUESTO Para obtener piezas de repuesto, llame a nuestro departamento de servicio al cliente al 1-877-319-3757, 7:30 a.m.- 4:30 p.m. CST, Lunes - Viernes. PIEZA DESCRIPTION PIEZA # RP 00614DCH RP 00614DSS RP 00614DMB RP 00612DCH RP 00612DSS RP 00612DMB Cabezal del rociador Soporte del rociador y el tornillo RP 00608DCH...

Este manual también es adecuado para:

255-k821-ss-t255-k821-mb-t