Service; Safety Messages; Introduction - GBC B1 Manual De Instrucciones De Operación

Safety messages

MAIN CORDSET SELECTION
(THE FOLLOWING NOTE ONLY APPLIES ONLY TO THE UNITS
RATED 230V 50Hz, AND LOCATED IN THE EUROPEAN UNION).
CAUTION: WHEN CHOOSING A DETACHABLE LINE CORD
FOR USE WITH YOUR MFPP-B1, ALWAYS FOLLOW THE
FOLLOWING PRECAUTIONS.
The cordset consists of three parts: the attachment plug, the cord and
the appliance inlet. Each of these components must have European
regulatory safety approvals.
The following minimum electrical ratings for the specific cordset are
published for safety purposes.
DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING
MINIMUM ELECTRICAL REQUIREMENTS.
PLUG: 3 amperes, 250 volts, 50/60 Hz, Class 1, 3 conductor, European
safety approved.
CORD: Type H05VV-F3G0.75, Harmonized (< HAR >). The "< >"
symbols indicate cord approved according to appropriate European
standard (NOTE: "HAR" may be substituted for approval mark of
European safety agency that approved the cord. An example would be
"< VDE >").
APPLIANCE CONNECTOR: 3 amperes, 250 volts, 50/60 Hz, European
safety approved, Type IEC 320. The cordset shall not exceed 3 meters
in length. A cordset with component electrical ratings greater than the
minimum specified electrical ratings may be substituted
FCC NOTE
(THE FOLLOWING NOTE ONLY APPLIES TO THE UNITS RATED
115V 60Hz.)
This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the Operation Manual,
may cause harmful interference with radio communications. Operation
of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his/her own expense.
CAN ICES-3 (A)/NMB-3(A)
CAUTION: ANY MODIFICATIONS MADE TO THIS DEVICE
THAT ARE NOT APPROVED BY GBC MAY VOID THE
AUTHOIRITY GRANTED TO THE USER BY THE FCC
AND/OR INDUSTRY CANADA TO
EQUIPMENT.
Service, MFPP-B1
Do not attempt to service your MFPP-B1 yourself. Contact an authorized
service representative for any required repairs or major maintenance for
your MFPP-B1.
DO NOT REMOVE THE MACHINE'S COVER.
There are NO user-serviceable parts inside the machine in order to avoid
potential personal injury and/or damage to property or the machine itself.
Service, Diesets
Every dieset is thoroughly oiled at the factory prior to shipping. Please
note that it is normal for oil to be present on the first few punched sheets.
During normal use this oil will be exhausted and should be replaced. As
part of regular maintenance, each dieset should be oiled after
approximately 250K punch cycles or sooner. Canon recommends use of
brand 3-IN-ONE oil as it is readily available. Other light machine oils can
also be used.
Multi Function Professional Puncher – B1
.
OPERATE THIS
To oil the dieset, refer to Section 8- Die Set User manual. Please note
that it is normal for oil to be present on the first set of sheets punched
after oiling the dieset. After approximately 25 to 50 sheets oil will no
longer be found on the punched sheet. At this time the MFPP-B1 can be
utilized for punching of print jobs.
Refer to Section 8 - Die Set User manual for detailed cleaning
instructions of the crease die.
See Section 8 MFPP-B1 Dieset Manual for further instructions on
servicing the Diesets.

2. INTRODUCTION

Thank you for purchasing the MFPP-B1. It is a versatile production
system that will enable you to punch documents for a variety of binding
styles by means of a simple die change. It has also been designed for
easy operation.
The MFPP-B1 is an innovative solution for punching paper and offers the
following design features:

Quick-change die sets that can be interchanged without any tools.

All MFPP-B1 die sets include an Identification Label providing the
user with the hole pattern and name.

Convenient storage area for two extra Die Sets located above the
sheet bypass.
Duty Cycle and Product Positioning
The CANON Multi Function Professional Puncher – B1 provides a
flexible, cost effective punching solution for light to medium level
punching production environments. It is designed for production print
users that typically punch their documents at an average of 20-30% of
their overall workflow. For customers that run continuous punching for
long runs of over 4 hours, performance may vary or degrade due to a
wide range of media weights and environmental conditions that can
occur.
Maximum Recommended Monthly Volume - The maximum
recommended monthly punch volume should NOT exceed 400,000.
Operating Die Set Supplies
Dies are considered consumables and when worn, must be replaced
since sharpening is not possible.
Each die set has a 90-day warranty from the date of purchase. The
warranty is void if the die is used beyond its specifications.
Punch die life will be maximized if oiled every 250,000 punch cycles or
sooner. (see Dieset Service for details)
Punch die sets have an expected use life of 750,000 punches using
20 lb/75 gsm paper. Crease die sets have an expected life of 500,000
cycles. This is a minimum life expectation only. Die life is NOT
guaranteed due to a wide range of media weights and environmental
conditions that the dies may endure. If you are going to be punching
extended runs that exceed the die use life, it is strongly recommended
that you have sufficient numbers of the appropriate die sets on hand to
continue with minimal downtime.
EN
4