Layout And Items Supplied - EINHELL TC-CS 1410 Manual De Instrucciones Original

king order, have the saw serviced before
you use it. Damaged parts, sticky deposits
or accumulations of chips will result in the
bottom guard hood working with a delay.
c) Open the bottom safety hood by hand
only for special cuts, such as "immersion
and angle cuts". Open the bottom guard
hood using the lever and release the lever
again as soon as the saw blade has plun-
ged into the workpiece. The bottom safety
hood must operate automatically for all other
sawing work.
d) Do not place the saw on a workbench
or on the floor unless the bottom guard
hood is covering the blade. An unprotec-
ted, moving saw blade will cause the saw to
move opposite to the sawing direction and
saw through anything in its way. Remember
that the saw blade takes a little time to slow
down and stop.
Additional safety instructions for all saws
with splitter
Function of the splitter
a) Use the right saw blade for the splitter.
For the splitter to work effectively, the saw
plate of the saw blade must be thinner than
the splitter and the tooth pitch must be grea-
ter than the thickness of the splitter.
b) Adjust the splitter as described in this
operating manual. Incorrect strength, po-
sition and alignment could lead to inefficient
recoil prevention.
c) Always use the splitter except for plunge
cuts. Re-attach the splitter after the plunge
cut. The splitter is disruptive when making
plunge cuts, and can lead to a recoil.
d) In order for the splitter to function, it must
be situated in the sawing gap. For shorter
cuts the splitter is ineffective for recoil preven-
tion.
e) Do not operate the saw if the splitter is
bent. Even a very small fault can cause the
guard hood to close more slowly.
•
Wear a protective dust mask!
•
Make sure that the splitter is adjusted so that
its distance to the saw blade gear rim does
not exceed 5 mm and the gear rim does not
project over the bottom of the splitter by more
than 5 mm.
•
When you want to cut wood or similar mate-
rials, use only saw blades which are recom-
mended by the manufacturer and comply with
EN 847-1.
Anl_SA_TC_CS_1410_SPK8.indb 30 Anl_SA_TC_CS_1410_SPK8.indb 30
GB
Do not lose these safety instructions.

2. Layout and items supplied

2.1 Layout (Fig. 1a/1b)
1. Handle
2. ON/OFF switch
3. Locking button for ON/OFF switch
4. Locking screw for cutting depth setting
5. Power cable
6. Soleplate
7. Locking lever for miter setting
8. Locking screw for parallel stop
9. Scale for miter angle
10. Additional handle
11. Guard hood
12. Saw blade
13. Saw blade wrench
14. Connection for sawdust extractor
15. Lever for the swing guard hood
16. Parallel stop
17. Screw for securing the saw blade
18. Clamping flange
19. Swing guard hood
20. Splitter
21. Spindle lock
22. 16mm blade holder
23. 30mm blade holder
2.2 Items supplied
Please check that the article is complete as
specified in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
the latest within 5 working days after purchasing
the product and upon presentation of a valid bill
of purchase. Also, refer to the warranty table in
the service information at the end of the operating
instructions.
•
Open the packaging and take out the equip-
ment with care.
•
Remove the packaging material and any
packaging and/or transportation braces (if
available).
•
Check to see if all items are supplied.
•
Inspect the equipment and accessories for
transport damage.
•
If possible, please keep the packaging until
the end of the guarantee period.
- 30 -
02.12.2021 15:27:09 02.12.2021 15:27:09