Layout And Items Supplied - EINHELL TC-SM 2131/1 Dual Manual De Instrucciones Original

•
Only fit blades which are well sharpened and
have no cracks or deformations.
•
Faulty saw blades must be replaced imme-
diately.
•
Never use saw blades which do not comply
with the data specified in this manual.
•
Note the direction of rotation of the motor and
saw blade.
•
It is imperative to make sure that the arrow
(direction of rotation) on the saw blade con-
forms with the arrow on the machine.
•
Pull out the power plug and twist the blade
with your hand into the 45° and 90° positions
in order to make sure that the blade does not
touch the turntable in any position. If necessa-
ry, readjust the saw head.
•
It is imperative to make sure that all devices
which cover the saw blade are in good wor-
king order.
•
Never wedge the hinged guard hood in open
position.
•
Never dismantle the machine's safety devices
or render them inoperative.
•
Never cut workpieces which are too small to
clamp securely on the saw table.
•
Avoid placing your hands in hazardous posi-
tions in which one or both hands could touch
the saw blade if they slip suddenly.
•
There must be no nails or other foreign bo-
dies in the workpiece.
•
Always stand to the side of the saw blade
when working with the saw.
•
Never load the machine so much that it cuts
out.
•
Always clamp the workpiece securely on the
saw table with a workpiece clamping device
in order to prevent the workpiece wobbling or
twisting.
•
Ensure that the off-cuts can be removed to
the side of the saw blade. Otherwise it is pos-
sible that they will be caught by the saw blade
and be catapulted out of the machine.
•
Never saw more than one workpiece at any
one time.
•
Never remove loose splinters, chips or jam-
med pieces of wood when the saw blade is
running.
•
To rectify faults or remove jammed pieces of
wood, always switch off the machine first. Pull
out the power plug!
•
Carry out retooling work, adjustments, mea-
surements and cleaning jobs only when the
motor is switched off. Pull out the power plug!
•
Switch off the motor and pull the power plug
before you leave the workplace.
Anl_TC_SM_2131_1_Dual_SPK8.indb 42 Anl_TC_SM_2131_1_Dual_SPK8.indb 42
GB
•
Damaged or faulty safety devices have to be
replaced immediately.
•
Damaged safety devices and parts must be
repaired or replaced by an authorized service
center.
•
Have damaged switches replaced by a custo-
mer service workshop.
•
This tool complies with the pertinent safety
regulations. Only a qualified electrician using
original replacement parts is are allowed to
carry out repairs. Failure to observe this point
may result in accidents for the user.
•
Refit all guards and safety devices immedia-
tely after you have completed any repairs or
maintenance work.
•
Be sure to observe the safety information
and operating and maintenance instructions
issued by the manufacturer, as well as the
dimensions listed in the Technical Data.
•
It is imperative to observe the accident pre-
vention regulations in force in your area as
well as all other generally recognized rules of
safety.
•
Operation in enclosed areas is permitted
only with a suitable vacuum extraction sys-
tem.
•
Do not use any low-powered machines for
heavy duty work.
•
Do not use the cable for purposes for which it
is not designed!
•
Check that the moving parts are in good wor-
king order, that they do not jam, and that no
parts are damaged. Make sure that all parts
are fitted correctly and that all other operating
conditions are properly fulfilled.
•
Caution: Take extra care when making double
miter cuts!
Please keep these safety instructions in a
safe place

2. Layout and items supplied

2.1 Layout (Fig. 1-17)
1. Handle
2. On/OFF switch
3. Release lever
4. Machine head
5. Saw shaft lock
6. Adjustable blade guard
7. Saw blade
8. Clamping device
9. Locking screw for stop rail
- 42 -
09.07.2020 11:13:38 09.07.2020 11:13:38