Descargar Imprimir esta página

Especificación Técnica; Technical Features; Instalación - Selecta DIGITHEAT 19L Manual De Instrucciones

Estufas de conveccion natural para desecacion y esterilizacion con regulacion y lectura digitalde temperatura y tiempo

Publicidad

MANUAL DE INSTRUCCIONES CODIGO 80034 REV A 05/03/99
ESPECIFICACIÓN TÉCNICA
Tensión de alimentación 115-230V 50/60 Hz se-
gún se indique en la placa de características de
la máquina.
Cap acidad /
Temperatura máxim a /
*Hom ogeneidad /
*Estabilidad /
Error de co nsigna /
Resolu ció n /
Medidas interiores
Internal dimensions
cm .
Medidas exterio res
Overall dimensions
cm .
Con sum o /
Peso /
* Medido según procedimiento de medida de J.P.
Selecta, s.a.
INSTALACIÓN
Colocar la estufa sobre una superficie plana, horizontal
y nivelada, procurando dejar un espacio libre de 10 cm.
por la parte posterior y por los laterales del equipo.
Para un mejor funcionamiento de la estufa no situarla
en lugares expuestos directamente al sol ni a fuentes
de calor.
Para su óptimo fucionamiento la Tª ambiente no debe
sobrepasar los 30ºC.
¡ATENCIÓN! IMPORTANTE PARA SU SEGURIDAD
CAUTION!!! IMPORTANT FOR YOUR SAFETY
No utilizar el aparato para el secado o tratamiento
de productos que puedan desprenden vapores o
formar mezclas explosivas o inflamables.
Asegúrese que el equipo se conecta a una tensión
de red que coincide con la indicada en la placa
de características.
No utilice el equipo sin estar conectada la toma
de tierra.
Si cambia la clavija de enchufe tenga en cuenta
lo siguiente:
Cable azul: Neutro.
Cable marrón: Fase.
Cable amarillo/verde: Tierra.
J
.P. SELECTA s.a.
capacity
(L.)
Maximum temperature
Homogeneity
Stability
Thermometer error
Resolution
Height
Alto /
Length
Ancho /
Width
Fo ndo /
Alto /
Height
Ancho /
Length
Width
Fo ndo /
Consumption
(W.)
Weight
(Kg.)
Ctra. NII Km 585.1 Abrera 08630 (Barcelona) España
e-mail: jpselecta@sefes.es - http://www.sefes.es/selecta
(Sujetas a modificaciones sin previo aviso)

TECHNICAL FEATURES

Voltage supply 115-230V 50/60 Hz according to
the characteristics plate indications.
2001241
2001242
2001243
19
36
250ºC
± 2%
± 0,25 ºC
± 2%
1ºC
30
40
25
30
25
30
50
60
60
65
44
49
600
900
1000
24
33
* Measured according to the measurement of J.P.
Selecta, s.a.
INSTALLATION
Put the oven on a flat , horizontal, level surface leaving
a space of about 10 cm at the back of the apparatus.
For a better oven function, do not situate it in places
where it can be directly exposed to the sun radiation or
heat sources.
For an optimum function the ambient temperature must
not be over 30ºC.
Do not use the oven to dry or for thermal treatment
of products which can give off vapours capable of
making an explosive mixture.
Be sure that the voltage supply is the same as the
one indicated on the characteristics plate.
Do not use the apparatus if it is not earthed.
If you change the plug bear the following in mind:
Blue cable: Neutral.
Brown cable: Phase.
Yellow/green cable: Earth.
2001244
2001244
52
80
150
33
50
50
47
40
60
33
40
50
53
70
70
82
74
95
52
59
68
1200
2000
40
51
68
Tel (34 3) 770 08 77 Fax (34 3) 770 23 62
Pag.: 4

Publicidad

loading