Decommissioning; Information For Service Technicians; Software - Rancilio KRYO 65 OD EVO Manual De Instrucciones

a crema, while grounds that are too fi ne result in strong, dark
coff ee without a crema;
- If the coff ee does not respond to your desired requirements,
adjust grind fi neness by pressing the ring block button (Fig. 2-1)
and turning the regulation knob (Fig. 2-3) counter- clockwise
for a fi ner grind or clockwise for a coarser grind;
- Repeat the operation until you have obtained the desired
quality of coff ee.
Recalibration of the grind is typically necessary after a change
in coff ee. Minor adjustments may be required throughout use to
accommodate for changes in freshness of the beans.

8. DECOMMISSIONING

8.1. Temporary
- Close the hopper and grind the coff ee beans remaining between
the burrs;
- Turn off the switch and unplug the appliance from the power
source;
- Remove any coff ee beans remaining in the bean hopper and
in the outlet;
- Perform cleaning and maintenance operations;
- Coil up the supply cable and attach it to the machine using
adhesive tape;
- Cover the machine and place it in a dry place, sheltered from
bad weather and to which you have exclusive access.
8.2. Final
In addition to the operations of temporary decommissioning:
- Cut the power cable;
- Pack up the machine using cardboard or similar materials
and hand it over to specialized operators (authorized waste
disposal collectors or dealers in second-hand goods).

9. INFORMATION FOR SERVICE TECHNICIANS

9.1. Replacement of burrs
Although manufactured in tempered steel, the burrs are subject
to wear and tear.
Their lifespan is infl uenced by the amount of coff ee ground, its
hardness and degree of roasting, as well as the quantity and purity
of the coff ee beans.
Small stones and various impurities have a marked abrasive action
which signifi cantly reduces the lifespan of the burrs.
When grinding time becomes noticeably longer or the grind
becomes irregular, the burrs should be replaced as follows:
- Pull the hopper locking slide (Fig. 1–4);
- Start the grinder to grind the coff ee remaining between the
burrs;
- Once grinding has fi nished, turn off the machine and unplug
from the power source;
- Remove the regulation knob (Fig. 1–3);
- Turn the upper burr-holder (Fig. 4–1) counter-clockwise until
the upper grinder holder ring nut is completely out of the head;
- Unscrew the screws (Fig. 4–2) and remove the burrs (Fig. 4–3)
from the burr-holder;
- Carefully clean the burr supports, the burr-holder thread and
its housing;
- Position the new burrs in their holders and block them fi rmly
in place;
- Reassemble the machine, performing the previous steps in
reverse;
- Calibrate the new burrs and reset the counter.
9.2. Calibration of grinder burrs
To be performed after burr replacement
The grinders are tested with a medium grind setting, and need
8
to be readjusted. This operation should be carried out with the
bean hopper empty.
Remove the protection lid (Fig. 1-5), hold down the adjustment
unlock button (Fig. 2-1) and at the same time slowly turn the
adjustment knob (Fig. 2-3) counter-clockwise until the burrs
brush against each other. Release the button, turn the numbered
ring (Fig. 2-2) so that the starting point 0 is frontal; move the
adjustment knob (Fig. 2-3) in the opposite direction (clockwise).
9.3. Technician menu
Must be performed by a qualifi ed technician.
The access to the technician menu is given by switching off the
grinder. Switch on the main switch (Fig. 1-9) while pressing the
confi rmation button.

10. SOFTWARE

KRYO 65 OD EVO has three menus to operate with.
10.1 Programming buttons
To confi gure the KRYO 65 OD EVO the dose buttons will be used
with an additional function.
The single dose button (Fig. 1-12) will be used as "-" button, the
double dose button (Fig. 1-13) as "+" button and both buttons to
browse through the menu. The customized dose button (Fig. 1-
14) is used as confi rmation or ESC-button depending on the
menu accessed.
10.2 Dosing menu
In the dosing menu the amount of coff ee dispensed by one button
can be changed.
- Press the selected button for 3 seconds;
- Change the value of the specifi c button using "+" and "-";
- Confi rm the change with the confi rmation button (II).
10.3 Barista menu
Open the "Barista Menu" by pressing the confi rmation button
(Fig. 1-14) for 5 seconds.
Any additional information is given in the software tree below.
10.4 Technician menu
Must be performed by a qualifi ed technician.
The parameters with the grey background are only accessible for
the service technician
The access to this menu is given in another chapter of the manual.