Black and Decker KG115 Instrucciones Originales página 7

Fitting and removing the guard (fig. A & B)
Fitting
Place the tool on a table, with the spindle (5) facing up.
u
Place the spring washer (6) over the spindle and locate it
u
on the shoulder (7).
Place the guard (4) onto the tool as shown.
u
Place the flange (8) over the spindle with the protruding
u
pips towards the guard. Make sure that the holes in the
flange align with the screw holes.
Secure the flange with the screws (9). Make sure that the
u
screws are fully tight and that the guard can be rotated.
Removing
Use a screwdriver to remove the screws (9).
u
Remove the flange (8), guard (4) and spring washer (6).
u
Store these parts carefully.
Warning! Never use the tool without the guard.
Fitting the side handle
Screw the side handle (2) into one of the mounting holes
u
in the tool.
Warning! Always use the side handle.
Fitting and removing grinding discs, cutting discs
or sanding flap pads (fig. C - E)
Always use the correct type of disc for your application.
Always use discs with the correct diameter and bore size
(see technical data).
Fitting
Fit the guard as described above.
u
Place the inner flange (10) onto the spindle (5) as shown
u
(fig. C). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the disc (11) onto the spindle (5) as shown (fig. C).
u
If the disc has a raised centre (12), make sure that the
raised centre faces the inner flange.
Make sure that the disc locates correctly on the inner flange.
u
Place the outer flange (13) onto the spindle. When fitting
u
a grinding disc, the raised centre on the outer flange must
face towards the disc (A in fig. D). When fitting a cutting
disc, the raised centre on the outer flange must face away
from the disc (B in fig. D).
Keep the spindle lock (3) depressed and tighten the outer
u
flange using the two-pin spanner (14) (fig. E).
Removing
Keep the spindle lock (3) depressed and loosen the outer
u
flange (13) using the two-pin spanner (14) (fig. E).
Remove the outer flange (13) and the disc (11).
u
All manuals and user guides at all-guides.com
Fitting and removing sanding backing pads
(fig. E & F)
For sanding, a backing pad is required. The backing pad is
available from your BLACK+DECKER dealer as an accessory.
Fitting
u
u
u
u
u
Removing
u
u
Fitting and removing hubbed wheels and cups
Hubbed wheels and cups install directly on the M14 threaded
spindle (5).
Caution! To reduce the risk of damage to the tool, wheel
or brush must not touch guard when mounted or while
in use. Undetectable damage could occur to the accessory,
causing wires to fragment from accessory wheel or cup.
Fitting
u
u
Removing
u
u
Use
Warning! Let the tool work at its own pace. Do not overload.
u
u
(Original instructions)
Place the inner flange (10) onto the spindle (5) as shown
(fig. F). Make sure that the flange is correctly located on
the flat sides of the spindle.
Place the backing pad (15) onto the spindle.
Place the sanding disc (16) onto the backing pad.
Place the outer flange (13) onto the spindle with the raised
centre facing away from the disc.
Keep the spindle lock (3) depressed and tighten the outer
flange using the two-pin spanner (14) (fig. E). Make sure
that the outer flange is fitted correctly and that the disc is
clamped tightly.
Keep the spindle lock (3) depressed and loosen the outer
flange (13) using the two-pin spanner (14) (fig. E).
Remove the outer flange (13), the sanding disc (16) and
the backing pad (15).
Thread the hubbed wheel or cup on to the spindle (5) by
hand.
Keep the spindle lock (3) depressed and tighten the hub of
the wheel or cup with a wrench.
Keep the spindle lock (3) depressed and loosen the hub of
the wheel or cup with a wrench.
Remove the wheel or cup from the spindle (5).
Carefully guide the cable in order to avoid accidentally
cutting it.
Be prepared for a stream of sparks when the grinding or
cutting disc touches the workpiece.
ENGLISH
7