Publicidad
Idiomas disponibles
Idiomas disponibles
Labels on tool
:
The following pictograms are shown on the tool:
Warning! To reduce the risk of injury, the user must
read the instruction manual.
Additional safety instructions for batteries and
chargers
Batteries
Never attempt to open for any reason.
u
Do not expose the battery to water.
u
Do not store in locations where the temperature may
u
exceed 40 °C.
Charge only at ambient temperatures between 10 °C and
u
40 °C.
Charge only using the charger provided with the
u
appliance/tool. Using the wrong charger could result in an
electric shock or overheating of the battery.
When disposing of batteries, follow the instructions given
u
in the section "Protecting the environment".
Do not damage/deform the battery either by puncture or
u
impact, as this may create a risk of injury and fire.
Do not charge damaged batteries.
u
Under extreme conditions, battery leakage may occur.
u
When you notice liquid on the batteries carefully wipe the
liquid off using a cloth. Avoid skin contact.
In case of skin or eye contact, follow the instructions below.
u
Warning! The battery fluid may cause personal injury or
damage to property. In case of skin contact, immediately rinse
with water. If redness, pain or irritation occurs seek medical
attention. In case of eye contact, rinse immediately with clean
water and seek medical attention.
Chargers
Your charger has been designed for a specific voltage.
Always check that the mains voltage corresponds to the
voltage on the rating plate.
Warning! Never attempt to replace the charger unit with
a regular mains plug.
Use your Black & Decker charger only to charge the
u
battery in the tool with which it was supplied. Other
batteries could burst, causing personal injury and damage.
Never attempt to charge non-rechargeable batteries.
u
If the supply cord is damaged, it must be replaced by the
u
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
Do not expose the charger to water.
u
Do not open the charger.
u
Do not probe the charger.
u
The appliance/tool/battery must be placed in a well
u
ventilated area when charging.
All manuals and user guides at all-guides.com
$
Electrical safety
#
u
Features
This tool includes some or all of the following features.
Assembly
Warning! Before assembly, engage the spindle lock as
described below.
Fitting and removing a screwdriver bit (fig. B)
u
u
Fitting and removing a bit tip using the bit tip
holder (fig. B)
u
u
u
u
Use
Warning! Let the tool work at its own pace. Do not overload.
Charging the battery (fig. C)
The battery needs to be charged before first use and
whenever it fails to produce sufficient power on jobs that were
easily done before. When charging the battery for the first time,
or after prolonged storage, it will only accept an 80% charge.
The charger is intended for indoor use only.
Your charger is double insulated; therefore no earth
wire is required. Always check that the mains
voltage corresponds to the voltage on the rating
plate. Never attempt to replace the charger unit with
a regular mains plug.
If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised Black & Decker Service
Centre in order to avoid a hazard.
1. On/off switch with forward/reverse function
2. Spindle lock collar (KC9036)
2. Torque adjustment collar (KC9039)
3. Bit holder
4. Handle adjustment button
5. Handle
6. Battery cover
To fit a screwdriver bit (7), push it into the bit holder until it
locates.
To remove a screwdriver bit, pull it straight from the bit
holder.
To fit the bit tip holder (8), push it into the bit holder until it
locates.
To fit a bit tip (9), insert it into the bit tip holder (8).
To remove a bit tip, pull it from the bit tip holder.
To remove the bit tip holder, pull it straight from the bit
holder.
ENGLISH
7
Publicidad
