Publicidad
Idiomas disponibles
Idiomas disponibles
• Keep ventilation slots of the motor clean to
prevent overheating.
• Always check the blade for cracks or signs
of damage.
• Clean the side extension table tubes after
each use.
NOTE: NEVER attempt to service the internal
parts of the motor. Contact our company's
Customer Service Department for any motor
function problems or failures.
WAter puMp
MAIntenAnCe
DISCONNECT THE
POWER BEFORE MAINTENANCE OF
THE PUMP.
1. Disassemble the water pump to see if any
cracks or dirt are inside (see FIGURE 29).
2. Check if the water tubing is clogged where
the water cannot flow. Clear the tubing with
warm water.
3. Make sure pump is plugged in during use.
4. Make sure the in-take sponge filter is
cleaned after each use.
5. Pump clean/ fresh water for one minute
through the water pump and the blade guard
to prevent waste build-up and clogging.
Do not run the pump without water.
Front plate
accessory
Impeller
Impeller
lid
Sponge
FIGURE 29
All manuals and user guides at all-guides.com
dIAMond BLAdeS
1. Use only 10 in. wet continuous rim diamond
blade with this saw.
2. Arbor size is 5/8 in.—please choose the
right size to fit the inner flange.
3. Do not use wood sawing blade, or other
blades not suitable for ceramic, porcelain or
stone—severe body injury or the saw damage
may occur.
4. This saw comes with a standard blade that
is ideal for cutting ceramic tile. If your project
requires the cutting of other substrates (ex.
porcelain, slate, stone), it is recommended
that you use the specific type of blade for the
material being cut.
THE FOLLOWING ARE DIAMOND bLADE
SAFETY PRECAUTIONS:
• ALWAYS INSpECT BLADES for cracks or
uneven wear. Discard cracked, chipped or
bent blades!
• ALWAYS USE MANUFACTURER'S RECOM-
MENDATION for matching the right blade
with the right material being cut.
• INSPECT THE ARBOR SHAFT for uneven
wear before mounting the blade.
• ALWAYS USE BLADES WITH THE CORRECT
ARBOR SIzE on a compatible arbor shaft.
• ENSURE THE BLADE IS MOUNTED WITH
THE ROTATION ARROW IN THE PROPER
DIRECTION and is securely tightened with a
wrench.
• ALWAYS WEAR PROPER SAFETY
EqUIPMENT at all times when operating
the saw. Wear goggles and dust mask at all
times when operating saw.
• ALWAYS ENSURE A CONTINUOUS FLOW
OF WATER on both sides of the blade before
cutting any material.
• Do NoT opERATE THE SAW WITHoUT ALL
SAFETY GUARDS IN POSITION.
• Do NoT opERATE THE SAW WITH BLADES
LARGER OR SMALLER THAN RECOM-
MENDED.
Pump
• Do NoT CUT DRY WITH BLADES MARKED
shaft
"USE WET."
• DO NOT ExCEED MAxIMUM RPMS recom-
mended by the blade manufacturer.
• DO NOT FORCE THE MATERIAL into the
blade. Let the blade cut at its own speed.
• Do NoT CUT MATERIAL NoT RECoM-
MENDED BY THE BLADE MANUFACTURER.
TROUBLESHOOTING
IF THE SAW IS OVERHEATING:
• Turn saw off and let it rest until motor is
• Check and clean the ventilation slots,
IF THE SAW DOES NOT START:
• Check that the power switch is in the
• Check that the power cord is
• Confirm that the power source voltage is
IF WATER IS NOT FLOWING THROUGH THE
WATER PUMP:
• Make sure water in tray is high enough to
• Make certain the water valve connecting
• Check water hose for connection or clogs.
• Check that the power cord is plugged
• Check for excess debris on intake filter.
IF THE CUTTING TAbLE IS NOT
SLIDING SMOOTHLY:
• Thoroughly clean guide rails.
If problem continues, call our Customer
Service Department at 1-866-435-8665.
– 7 –
cool to the touch.
removing blockage and dirt.
"ON" position.
plugged in properly.
120V from outlet.
clear the intake nozzle.
the pump to the tubing is in the
"ON" position.
in properly.
Publicidad
