Cardin Elettronica ELSNAP RAPID S Manual De Instrucciones página 16

Terminal board connections
1-2 TPR power failure indication. Connect to transformer secondary.
SLAVE slave control output. Connect to ECU of second barrier .
3-4
LDA boom light output 24 Vdc 100 mA. Connect to boom LED lights,
5-6
if installed.
7-8 US1 (N.C.) multifunction output (max. 8A 230V).
US1 (N.O.) multifunction output (max. 8A 230V).
8-9
10 Mass conductor for radio receiver antenna.
11 Pole conductor for radio receiver antenna (if an external antenna is fitted
use a coaxial type cable RG58 with an impedance of 50Ω).
TD (N.O.) dynamic button input.
12
13 TA (N.O.) opening button input.
14 TC (N.O.) closing button input.
CMN common for all inputs and outputs.
15
CC (N.C./8.2 kΩ) closing safety edge input. Opening this contact will
16
provoke a travel direction inversion of a few degrees during the closing
stage. Jumper J4 pos. 2 = contact N.C. Jumper J4 pos. 1 = contact
8.2 kΩ. If not used set dip 3 CC to On (DS2).
All rights reserved. Unauthorised copying or use of the information contained in this document is punishable by law
17 TB (N.C.) stop button input (the opening of this contact interrupts the
cycle until a new movement command is given). If not used set dip 2
TB to On (DS2).
FT (N.C.) safety and control devices in input (photocells invert the travel
18
direction when an obstruction is detected). Opening this contact will
provoke a travel direction inversion during closure due to the cutting in
of the safety device. If not used set dip 1 FT to On (DS2)
BSP (N.C.) door safety switch input. The opening of this contact will
19
block all movement until the door is closed. Not installed at the moment.
If you need to install a door switch cut jumper J5 and connect this
input to the door safety microswitch.
20 CSB common for all security inputs.
TPR
SLAVE
D
LDA
NC
CMN
US1
NO
FC1
FC2
24V IN 4V ECU power supply input
DS1 Safety device disable dip-switches
DS2
Function selection dip-switches
FC1 Travel limit 1
FC2 Travel limit 2
F1 12,5A delayed cartridge fuse, motor power supply protection
F2 2A cartridge fuse 24V power supply protection
J1 Dynamic mode selection jumper for OC receiver card channel 1
J2 Opening mode selection jumper for OC receiver card channel 1
J3 ECU reset jumper
J4
N.C./8.2 kΩ selection jumper
SL2
F1
F2
P1 P3
L1
T1
+
J3
L2
L3
J1
J2
SL1
OC
21-22 Output for photoelectric cells CTRL24Vdc. Voltage is only present
when the boom is not closed.
23-24 Auxiliary device output 24Vdc. Voltage is always present here.
25-27 ENCODER encoder signal input - / + / data.
ALL UNUSED NC CONTACTS MUST BE JUMPED
• Switch on the power and make sure that the indicator LEDs are in the following
condition:
- L1 Programming Led
- L2 Indicator Led for the opening travel limit (FC1)
- L3 Indicator Led for the closing travel limit (FC2)
- L4 Indicator Led for the inverting photoelectric cells (FT)
- L5 Indicator Led for the blocking button (TB)
- L6 Indicator Led for the closing button (TC)
- L7 Indicator Led for the opening button (TA)
- L8 Indicator Led for the dynamic command (TD/CH1)
If no LEDs light up check the condition of the fuses and the power cable
connection at the transformer primary.
If one or more safety indicator Leds are off the safety device has been triggered.
* depends on the position of the boom.
Pos.1 Pos.2
P2
DS2
DIS. CTRL24
FT
TB
CC
TPR
DS1
Pos.1 Pos.2
TD
REG.VEL.
PRELAMP.
RIC. AUT.
INV. 8,2K NC
SLAVE
US1
TPR
FOTORIC.
J5 Jumper (bridged) door microswitch disabled
J6 Jumper Test. Remove this jumper Pos. 2 to enable control of the output
CTRL24Vdc
MOT 24V motor connection
OC RF open collector module, 433 / 868 MHz
P1 PROG/STOP button
P2 TD dynamic button
P3 Programming button
SL1 Internal led light connector
SL2 Internal led light connector
T1 Opening direction deceleration setting trimmer
16
CS19705 DC0595
(R)
(N)
D
J6 24Vdc
J5
CTRL24Vdc
CSB
BSP
NC
FT
L4
NC
TB
L5
NC
CC
NC
J4
CMN
TC
L6
NO
TA
L7
NO
TD
L8
NO
OFF
OFF/ON*
OFF/ON*
ON
ON
OFF
OFF
OFF
12