Publicidad
Idiomas disponibles
Idiomas disponibles
English
8. Check the rotational direction
The bit rotates clockwise (viewed from the rear side) by
pushing the R-side of the selector button.
The L-side of the selector button is pushed to turn the
bit counterclockwise (See Fig. 11) (The
marks are provided on the body).
9. Switch operation
○ When the trigger switch is depressed, the tool rotates.
When the trigger is released, the tool stops.
○ The rotational speed of the drill can be controlled by
varying the amount that the trigger switch is pulled.
Speed is low when the trigger switch is pulled slightly
and increases as the trigger switch is pulled more.
NOTE
A buzzing noise is produced when the motor is about to
rotate; This is only a noise, not a machine failure.
10. Using the hook
CAUTION
○ When using the hook, pay suffi cient attention so that
the main equipment does not fall. If the tool falls, there
is a risk of accident.
○ Do not attach the tip tool except phillips bit to the tool
main unit when carrying the tool main unit with the hook
suspended from a waist belt.
Injury may result if you carry the equipment suspended
from the waist belt with sharp tipped components such
as drill bit attached.
The hook can be installed on the right or left side and the
angle can be adjusted in 5 steps between 0° and 80°.
(1) Operating the hook
(a) Pull out the hook toward you in the direction of arrow
(A) and turn in the direction of arrow (B) (Fig. 12).
(b) The angle can be adjusted in 5 steps (0°, 20°, 40°,
60°, 80°).
Adjust the angle of the hook to the desired position
for use.
(2) Switching the hook position
CAUTION
Incomplete installation of the hook may result in bodily
injury when used.
(a) Securely hold the main unit and remove the screw
using a slotted head screwdriver or a coin (Fig. 13).
(b) Remove the hook and spring (Fig. 14).
(c) Install the hook and spring on the other side and
securely fasten with screw (Fig. 15).
NOTE
Pay attention to the spring orientation. Install the spring
with larger diameter away from you (Fig. 15).
(3) Using the bit holder (Hook with bit holder)
○ Installing the bit
Slide the bit from the side and then insert fi rmly until the
groove on the bit locks in the protruded section of the
hook.
○ Removing the bit
Securely hold the main unit and pull out the bit by
holding the tip with your thumb (Fig. 16).
CAUTION
Only Hitachi STANDARD ACCESSORIES phillips bit
(No. 2 × 65L; Code No. 983006) may be used. Do not
use other bits since they may come loose.
(4) Using as an auxiliary light (Hook with light)
(a) Press the switch to turn off the light.
If forgotten, the light will turn off automatically after
15 minutes.
(b) The direction of the light can be adjusted within the
range of hook positions 1 - 5 (Fig. 17).
○ Lighting time
AAAA manganese batteries: approx. 15 hrs.
AAAA alkali batteries: approx. 30 hrs.
12
CAUTION
Do not look directly into the light.
Such actions could result in eye injury.
(5) Replacing the batteries
and
(a) Loosen the hook screw with a phillips-head
screwdriver (No. 1) (Fig. 18).
Remove the hook cover by pushing in the direction
of the arrow (Fig. 19).
(b) Remove the old batteries and insert the new
batteries. Align with the hook indications and
position the plus (+) and minus (–) terminals
correctly (Fig. 20).
(c) Align the indentation in the hook main body with
the protuberance of the hook cover, press the hook
cover in the direction opposite to that of the arrow
shown in Fig. 19 and then tighten the screw.
Use
commercially
(1.5 V).
NOTE
Do not tighten the screw excessively. Such action could
strip the screw threads.
CAUTION
○ Failure to observe the following can result in battery
leakage, rust or malfunction.
Position the plus (+) and minus (–) terminals correctly.
Replace both batteries at the same time. Do not mix old
and new batteries.
Remove
immediately.
○ Do not discard batteries together with normal trash and
do not throw batteries into fi re.
○ Store batteries out of the reach of children.
○ Use batteries correctly in accordance with the battery
specifi cations and indications.
11. Using the bit holder
CAUTION
○ Stow the bit in the specifi ed location on the tool. If the
tool is used with the bit stowed improperly, the bit may
fall and cause bodily injury.
○ Do not stow bits that are of a diff erent length, gauge or
dimension than the plus driver bit (65 mm long) included
in the STANDARD ACCESSORIES.
The bit may fall and cause bodily injury.
(1) Removing the bit
Securely hold the main unit and pull out the bit by
holding the tip with your thumb (Fig. 21).
(2) Installing the Bit
Install the bit with steps opposite of when removing.
Insert the bit so that the right and left sides are equal, as
shown in Fig. 22.
MAINTENANCE AND INSPECTION
1. Inspecting the tool
Since use of as dull tool will degrade effi ciency and
cause possible motor malfunction, sharpen or replace
the tool as soon as abrasion is noted.
2. Inspecting the mounting screws
Regularly inspect all mounting screws and ensure that
they are properly tightened. Should any of the screws
be loose, retighten them immediately. Failure to do so
could result in serious hazard.
3. Cleaning on the outside
When the driver drill is stained, wipe with a soft dry
cloth or a cloth moistened with soapy water. Do not use
chloric solvents, gasoline or paint thinner, for they melt
plastics.
4. Storage
Store the driver drill in a place in which the temperature
is less than 40°C and out of reach of children.
available
exhausted
batteries
AAAA
batteries
from
the
hook
Publicidad
